Filter
Top Products
71
2. After the configuration, press the MON (ESC) button.
The monitor display will return to the previous menu.
After all the configurations, press the SETUP button while
holding down the SHIFT button. The configuration will be
updated when closing SETUP MENU.
Notes:
• When moving the joystick to ▼ at the bottom of CAM-
ERA TITLE 1 of 2, the monitor will display 2 of 2 (the
next page).
• When moving the joystick to ▲ at the top of CAMERA
TITLE 2 of 2, the monitor will display 1 of 2 (the previous
page).
• Original characters are configurable through WJ-
SX150A Administrator Console, but they are not dis-
played correctly in SETUP MENU. They are displayed
as ■. (Refer to p. 95 Edit Font window.)
• The titles of the camera channels deactivated by the
master-slave connection are displayed as “- - -“.
■ RECORDER
■ CAMERA TITLE
● How to Display
To display this menu on the monitor, move the cursor to 500
CAMERA TITLE in SETUP MENU by moving the joystick to
▼ or ▲. Then, press the CAM (SET) button. The submenu
appears on the monitor.
● How to edit
Move the joystick to move the cursor.
To select parameters, press the PREV or NEXT button.
SWITCHER: Select a unit (SLAVE1 to 4 and MASTER*)
to configure the parameters.
* In normal connection, only MASTER is displayed.
CAM: This stands for a camera channel of the unit.
LCN: This stands for a logical camera number. 1 to 99
is selectable.
TITLE: A camera title is composed of up to 20 charac-
ters. Each camera number is fixed and the subse-
quent 20 characters are editable.
The characters available here are the following:
ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrs
tuvwxyz0123456789!"#$%&'()*+,-./:;=?•_(space)
The factory default settings are same as the illustrations.
1. Edit the camera titles by pressing the NEXT or PREV
buttons.
The NEXT button toggles these characters in this order.
The PREV button toggles these characters in a reverse
order.
Joystick and the CLEAR button are also usable for the
edit. (Refer to p. 63 Displaying SETUP MENU for each
use.)
500 CAMERA TITLE 1 of 2
SWITCHER=MASTER(2 of 2)
CAM LCN TITLE
1 -- ---
2 -- ---
3 -- ---
4 -- ---
5 17
6 18
7 19
8 20
LCN:LOGICAL CAMERA NUMBER
500 CAMERA TITLE 2 of 2
SWITCHER=MASTER(2 of 2)
CAM LCN TITLE
9 21
10 22
11 23
12 24
13 25
14 26
15 27
16 28
LCN:LOGICAL CAMERA NUMBER
600 RECORDER
CONTROL ADR EXT IN
610 MASTER ---
620 SLAVE1 HD100 01
630 SLAVE2 OFF GENLOCK OFF
640 SLAVE3 VCR
650 SLAVE4 HD500 01 GENLOCK OFF
--COMMUNICATION STATUS--
DATA BIT 7bit
PARITY BIT ODD
STOP BIT 1bit
BAUD RATE 9600bps
COMM PORT SERIAL PORT
● How to Display
To display this menu on the monitor, move the cursor to 600
RECORDER in SETUP MENU by moving the joystick to D
or C. Then, press the CAM (SET) button. The submenu will
appear on the monitor.
● Parameters
Move the joystick to move the cursor.
Press the NEXT or PREV button to select the desired para-
meters.
Press the numeric button(s) to enter a number.
• 610 MASTER/620 SLAVE1/630 SLAVE 2/640
SLAVE 3/650 SLAVE 4
This stands for the type of units connected in the sys-
tem.
CONTROL: This stands for the recorder connected to
each unit. The selectable parameters will differ
depending on whether a Multiplexer board is
installed in the unit.