Filter
Top Products
107
SYSTEM SETTINGS
8
5
Enter the recall interval (01 to 15)* with the
numeric keys and then press the [OK] key.
• The recall interval can be set from 1 to 15* minutes.
•
After finishing step 5, if you do not wish to change the
number of recall attempts, press the [BACK] key to exit.
* Varies depending on country and region.
6
Select "RECALL TIMES" with the [ ] or
[ ] key and then press the [OK] key.
7
Enter the number of recall attempts with the
numeric keys and then press the [OK] key.
• If you do not wish to have recalling take place, set the
number of attempts to "0".
RECALL SET (ERR)
When sending a fax, this setting is used to select
whether or not the machine will automatically
re-attempt the call if the transmission fails due to a line
error. Normally the machine is set to make 1* recall
attempt at intervals of 1* minute.
If you do not wish to have recalling take place, set the
number of attempts to "0" (steps 6 and 7).
* Varies depending on country and region.
1
Follow steps 1 through 6 of "INITIAL
PROCEDURE" (page 98).
2
Select "SENDING FUNCTION" with the [ ]
or [ ] key and then press the [OK] key.
3
Select "RECALL SET(ERR)" with the [ ]
or [ ] key and then press the [OK] key.
If you do not wish to change the recall interval setting,
go to step 6.
4
Select "RECALL INTERVAL" with the [ ]
or [ ] key and then press the [OK] key.
5
Enter the recall interval (00 to 15) with the
numeric keys and then press the [OK] key.
• The recall interval can be set from 0 to 15 minutes.
•
After finishing step 5, if you do not wish to change the
number of recall attempts, press the [BACK] key to exit.
6
Select "RECALL TIMES" with the [ ] or
[ ] key and then press the [OK] key.
7
Enter the number of recall attempts with the
numeric keys and then press the [OK] key.
• If you do not wish to have recalling take place, set the
number of attempts to "0".
• If the recall interval is set to "0", the machine will
immediately call again after the connection is broken
due to the line error.
RING TIMEOUT IN AUTO TX
When sending a fax by automatic transmission (see
"Storing transmission jobs (memory transmission)" on
page 23), this setting lets you select the amount of
time that the machine waits before breaking the
connection when the other machine does not answer
your machine's call. If the other machine does not
respond within this set time, your machine will
automatically break the connection.
Time selections are "30 SEC.", "45 SEC." and "60 SEC.".
Normally "45 SEC." is selected.*
* Varies depending on country and region.
1
Follow steps 1 through 6 of "INITIAL
PROCEDURE" (page 98).
2
Select "SENDING FUNCTION" with the [ ]
or [ ] key and then press the [OK] key.
3
Select "RING TIMEOUT IN AUTO TX" with
the [ ] or [ ] key and then press the [OK]
key.
4
Select the time with the [ ] or [ ] key and
then press the [OK] key.
Selections for the call time are "30 SEC.", "45 SEC.",
"60 SEC.".
*
* Varies depending on country and region.
•
If you made a mistake in step 5 or step 7,
move the cursor to the mistake with the [ ]
or [ ] key and enter the correct number.
• Even if this setting is enabled, the
machine will not re-attempt the call when
a fax is sent by manual transmission.
Note
• If you made a mistake in step 5, move the
cursor to the mistake with the [ ] or [ ]
keys and enter the correct number.
• Even if this setting is enabled, the
machine will not re-attempt the call when
a fax is sent by manual transmission.
Note