Filter
Top Products
Chapter 5 Operation Procedures
III-11
5
5
5
.
.
.
4
4
4
.
.
.
1
1
1
S
S
S
t
t
t
o
o
o
p
p
p
p
p
p
i
i
i
n
n
n
g
g
g
t
t
t
h
h
h
e
e
e
S
S
S
e
e
e
r
r
r
v
v
v
e
e
e
r
r
r
Stop the business server connected to the disk array.
5
5
5
.
.
.
4
4
4
.
.
.
2
2
2
S
S
S
e
e
e
t
t
t
t
t
t
i
i
i
n
n
n
g
g
g
a
a
a
D
D
D
i
i
i
s
s
s
k
k
k
A
A
A
r
r
r
r
r
r
a
a
a
y
y
y
Depending on the operating environment, it is necessary to set the disk array. For information on the parameters,
refer to 6.1 "Parameters". Before changing the settings, carefully read the disk array manual until they are fully
understood. For how to set the disk array, refer to Chapter 9 "Configuration Setting (Common to All Units)".
5
5
5
.
.
.
4
4
4
.
.
.
3
3
3
S
S
S
e
e
e
t
t
t
t
t
t
i
i
i
n
n
n
g
g
g
t
t
t
h
h
h
e
e
e
P
P
P
o
o
o
r
r
r
t
t
t
A
A
A
c
c
c
c
c
c
e
e
e
s
s
s
s
s
s
M
M
M
o
o
o
d
d
d
e
e
e
Set the port access mode. Set the port mode to the WWN mode or Port mode depending on your operation. For
specific procedures, refer to 10.1 "Changing the Port Mode".
5
5
5
.
.
.
4
4
4
.
.
.
4
4
4
C
C
C
r
r
r
e
e
e
a
a
a
t
t
t
i
i
i
n
n
n
g
g
g
a
a
a
n
n
n
L
L
L
D
D
D
S
S
S
e
e
e
t
t
t
Create an LD Set. Use the LD Set type supporting your business server OS. It is recommended to specify the
business server name for the LD Set name. For specific procedures, refer to 10.2.1 "Setting an LD Set".
5
5
5
.
.
.
4
4
4
.
.
.
5
5
5
L
L
L
i
i
i
n
n
n
k
k
k
i
i
i
n
n
n
g
g
g
a
a
a
n
n
n
L
L
L
D
D
D
S
S
S
e
e
e
t
t
t
a
a
a
n
n
n
d
d
d
P
P
P
a
a
a
t
t
t
h
h
h
Link a path to the created LD Set. Link the WWPN for the HBA port in the business server to the LD Set in the
WWN mode. Link the disk array port connected to the business server to the LD Set in the Port mode. For specific
procedures, refer to 10.2.2 "Linking an LD Set and Path".
5
5
5
.
.
.
4
4
4
.
.
.
6
6
6
A
A
A
s
s
s
s
s
s
i
i
i
g
g
g
n
n
n
i
i
i
n
n
n
g
g
g
a
a
a
L
L
L
o
o
o
g
g
g
i
i
i
c
c
c
a
a
a
l
l
l
D
D
D
i
i
i
s
s
s
k
k
k
Assign a logical disk to the created LD Set. Assign the logical disk accessed from the business server to the LD Set.
For specific procedures, refer to 10.3.1 "Assigning a New Logical Disk".