Filter
Top Products
P R E L I M I N A R Y
AMD
131Am79C930
AC CHARACTERISTICS
5.0 AND 3.3 V PCMCIA INTERFACE
ABSOLUTE MAXIMUM RATINGS
Storage Temperature: –65 to +150*C. . . . . . . . . . . .
Ambient Temperature Under Bias: –65 to +125*C. . .
Supply Voltage to AVSS
or DVSS (AVDD, DVDD): –0.3 to +6 V. . . . . . . . . . . . . .
Stresses above those listed under Absolute Maximum
Ratings may cause permanent device failure. Functionality at
or above these limits is not implied. Exposure to Absolute
Maximum Ratings for extended periods may affect
device reliability.
OPERATING RANGES
Commercial (C) Devices
Temperature (T
A)0°C to + 70°C. . . . . . . . . . . . . . . . .
Supply Voltages (V
CC, VDDT, VDDU1, VDDU2, VDDM, VDDP)
3.0 V to 5.25 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supply Voltages
(AV
DD, VDD5) +5 V ± 5%. . . . . . . . . . . . . . . . . . . . . . . .
All inputs within the range: V
SS – 0.5 V ≤ VIN ≤ VDD + 0.1 X
V
DD – where VSS and VDD are appropriate reference pins
for a given input pin. (See section on power supply
pin descriptions.)
CL = 50 pF unless otherwise noted
Operating ranges define those limits between which the func-
tionality of the device is guaranteed.
PCMCIA MEMORY READ ACCESS
Parameter
Symbol Parameter Description Test Conditions Min Max Unit
tAVQV Address access time Note 1 0 550 ns
tAVGL Address setup to OE ↓ 5ns
tGHAX Address hold from OE ↑ 20 ns
tELQV CE access time Note 1 0 550 ns
tELGL CE setup to OE ↓ 0ns
tGHEH CE hold from OE ↑ (READ) or
CE hold from WE ↑ (WRITE) 20 ns
tGLQV OE acess time Note 1 0 200 ns
tGLWTV WAIT valid from OE ↓ 35 ns
tWTLWTH WAIT pulse width Notes 2, 3 53 X TCLKIN ns
tGLQNZ Data Bus driven from OE Note 3 0 ns
tQVWTH Data setup to WAIT ↑ 0ns
tGHQZ Data disabled from OE ↑ Note 3 90 ns
Notes:
1. Assumes no wait state access is programmed.
2. The max value for this parameter assumes the following worst case situation:
Value Worst Case
0 FLASH and SRAM wait states set at “3.”
1 Host performs PCMCIA WRITE cycle at same time that Am79C930 embedded 80188 controller begins
instruction fetch cycle to FLASH memory.
2 PCMCIA WRITE cycle is posted internal to Am79C930 device, pending the completion of the embedded 80188
controller access.
3 Host performs PCMCIA READ cycle immediately following completion of PCMCIA WRITE cycle.
4 After completion of first embedded 80188 access to FLASH, posted PCMCIA WRITE executes to SRAM;
PCMCIA READ stycle is being held in wait state.
5 After completion of posted ISA WRITE cycle, new embedded 80188 access to FLASH begins.
6 After completion of second embedded 80188 access to FLASH, PCMCIA READ cycle is allowed to proceed onto
memory bus to SRAM; host is still held in wait state.
7 At SRAM READ cycle completion, data is delivered to PCMCIA bus and wait state is exited.
3. Parameter is not included in production test.