Filter
Top Products
P R E L I M I N A R Y
AMD
37Am79C930
ENXCHBSY bit of TCR28 and the CHBSYU bit of
TIR5 and operates independently of the bits in the
table below.
In addition to the functionality listed above, the
USER5/IRQ4/EXTCHBSY pin may be used as the
source for CCA information, instead of relying on the in-
ternal CCA logic of the Am79C930 device. When using
the external CCA information, CCA information from the
internal logic will be unavailable. External CCA informa-
tion will appear in the same register bit locations as in-
ternal CCA information, when enabled, so a change
from internal source to external source will be transpar-
ent to firmware (excepting the necessary change in the
ENXCHBSY bit value).
This source of CCA information is controlled by the
ENXCHBSY bit of TCR28. When the ENXCHBSY bit of
TCR28 is set to a 1, then the value of the
USER5/IRQ4/EXTCHBSY pin will be fed directly to the
CHBSYC bit of TIR4, CHBSY bit of TIR26 and the BCF
bit of TIR5. If the CHBSYC interrupt is unmasked, it will
produce an interrupt to the 80188 embedded controller.
If the BCF interrupt is unmasked, it will produce an inter-
rupt to the 80188 embedded controller. Note that setting
the ENXCHBSY bit of TCR28 to a 1 will cause the
USER5/IRQ4/EXTCHBYS pin to function as an input,
regardless of the settings of the other control
bits listed.
USER5/ USER5/
PCMCIA ENXCHBSY USER5FN USER5EN IRQ Select IRQ Type IRQ4 IRQ4
Pin TCR28[5] TCR7[5] TCR15[2] PnPx70 PnPx71 Direction Pin Data
0 1 X X X X I TIR11[5]
0 0 0 X 4h 2h O IRQ4
0 0 0 X 4h 1h OD IRQ4
0000≠4h X I TIR11[5]
0001≠4h X O TIR11[5]
0 0 1 0 X X I TIR11[5]
0 0 1 1 X X O TIR11[5]
1 1 X X X X I TIR11[5]
1 0 X 0 X X I TIR11[5]
1 0 X 1 X X O TIR11[5]
Pin 98: ACT
The ACT pin may be configured for input or output op-
eration. The output drive may be programmed for totem
pole or open drain operation. ACT pin configuration is
accomplished according to the following table:
Note that a read of the ACT bit (TIR0[6]) will always
give the current ACT pin value, regardless of pin
configuration setting.
ACTEN ACT ACTDR ACT Pin ACT Pin
TCR15[1] TIR0[6] TCR27[3] Direction Value
0X XI NA
1 0 0 OD float reset default condition
1 1 0 OD LOW
1 0 1 O HIGH
1 1 1 O LOW
Pin 100: LNK
The LNK pin may be configured for input or output op-
eration. The output drive may be programmed for totem
pole or open drain operation. LNK pin configuration is
accomplished according to the following table:
Note that a read of the LNK bit (TIR0[7]) will always
give the current LNK pin value, regardless of pin
configuration setting.
LNKEN LNK LNKDR LNK Pin LNK Pin
TCR13[7] TIR0[7] TCR27[4] Direction Value
0X XI NA
1 0 0 OD float reset default condition
1 1 0 OD LOW
1 0 1 O HIGH
1 1 1 O LOW