Filter
Top Products
Chapter 5 - Parameter List
5-6
5.3 Function 2 Group [FU2]
Keypad Display Setting Range
Code Description
LCD 7-Segment LCD 7-Segment
Units
Factory
Default
Adj.
During
Run
Page
FU2-00 Jump to desired code #
Jump code
Not displayed 1 to 94 Not available 1 1 Yes 6-2
FU2-01 Previous Fault History 1
Last trip-1
01
FU2-02 Previous Fault History 2
Last trip-2
02
FU2-03 Previous Fault History 3
Last trip-3
03
FU2-04 Previous Fault History 4
Last trip-4
04
FU2-05 Previous Fault History 5
Last trip-5
05
By pressing [PROG] and [▲] key,
the frequency, current, and
operational status at the time of fault
can be seen.
- None -
No 0
FU2-06 Erase Fault History
Erase trips
06
Yes 1
- No Yes
6-2
FU2-07 Dwell Frequency
Dwell freq
07 FU1-22 to FU1-20 0.01 5.00 [Hz] No
FU2-08 Dwell Time
Dwell time
08 0 to 10 [sec] 0.1 0.0 [sec] No
6-2
No 0
FU2-10
Frequency Jump
Selection
Jump freq
10
Yes 1
- No No
FU2-11
17
Jump Frequency 1 Low
Jump lo 1
11 FU1-22 to FU2-12 0.01 10.00 [Hz] No
FU2-12 Jump Frequency 1 High
Jump Hi 1
12 FU2-11 to FU1-20 0.01 15.00 [Hz] No
FU2-13 Jump Frequency 2 Low
Jump lo 2
13 FU1-22 to FU2-14 0.01 20.00 [Hz] No
FU2-14 Jump Frequency 2 High
Jump Hi 2
14 FU2-13 to FU1-20 0.01 25.00 [Hz] No
FU2-15 Jump Frequency 3 Low
Jump lo 3
15 FU1-22 to FU2-16 0.01 30.00 [Hz] No
FU2-16 Jump Frequency 3 High
Jump Hi 3
16 FU2-15 to FU1-20 0.01 35.00 [Hz] No
6-2
FU2-17
Start Curve for S-Curve
Accel/Dedel Pattern
Start Curve
17 1 to 100 [%] 1 40% No
FU2-18
End Curve for S-Curve
Accel/Dedel Pattern
End Curve
18 1 to 100 [%] 1 40% No
6-2
FU2-19
Input/Output Phase Loss
Protection
Trip select
19
00 to 11
(Bit Set)
- 00 Yes 6-2
No 0
FU2-20 Power ON Start Selection
Power-on run
20
Yes 1
- No Yes 6-2
No 0
FU2-21 Restart after Fault Reset
RST restart
21
Yes 1
- No Yes 6-2
FU2-22 Speed Search Selection
Speed Search
22
0000 to 1111
(Bit Set)
- 0000 No
FU2-23
Current Limit Level
During Speed Search
SS Sup-Curr
23 80 to 200 [%] 1 100 [%] Yes
FU2-24
P Gain
During Speed Search
SS P-gain
24 0 to 30000 1 100 Yes
FU2-25
I Gain
During speed search
SS I-gain
25 0 to 30000 1 1000 Yes
6-2
FU2-26
Number of Auto Restart
Attempt
Retry number
26 0 to 10 1 0 Yes 6-2
17
Code FU2-11 through FU2-16 appears only when FU2-10 is set to ‘Yes’.