Magnetek Quattro DC Elevator Drive Computer Hardware User Manual


 
Quattro DC Quick Parameter Reference
Menu Parameter Unit
D1 Elevator Data Submenu
D1 Speed Command ft/min or m/sec
D1 Speed Reference ft/min or m/sec
D1 Speed Feedback ft/min or m/sec
D1 Speed Error ft/min or m/sec
D1 Pre-Torque Ref % of rated torque
D1 Ext-Torque Cmd % of rated current
D1 Spd Reg Torq Cmd % of rated torque
D1 Tach Rate Cmd % of rated torque
D1 Aux Torque Cmd % of rated torque
D1 Est Inertia Seconds
D1 Rx Com Status 1 = true; 0 = false
D1 Logic Outputs 1 = true; 0 = false
D1 Logic Inputs 1 = true; 0 = false
D2 MS Power Data Submenu
D2 Armature Current Amps
D2 Field Current Amps
D2 Armature Voltage Volts
D2 MS Bus Voltage Volts
D2 Motor Mode None
D2 Torque Ref %
D2 Est Spd Fdbk ft/min or m/sec
D2 Encoder Spd ft/min or m/sec
D2 DS Module Temp °C
D2 LS Module Temp °C
D2 Highest Temp °C
D2 Field IGBT Temp °C
D2 Armature Cur Err Amps
D2 Auto Fld Int none
D2 Auto Fld Prop none
D2 Auto Meas Arm L mH
D2 Auto Meas Arm R Ohm
D2 Auto Field Res Ohm
D2 Auto Field Tc sec
D3 LS Power Data Submenu
D3 LS Pwr Output kW
D3 DC Bus Voltage Volts
D3 DC Bus Volts Ref Volts
D3 LS Overload %
D3 LS Input Current Amps
D3 LS D Axis I %
D3 LS Q Axis I %
D3 LS D Axis Volts %
D3 LS Q Axis Volts %
D3 Input Hz Hz
D3 Input Vab Volts
D3 Input Vca Volts
D3 LS Module Temp °C
Menu Parameter Unit
U1 Password U1 Submenu
U1 Enter password -
U1 New password -
U1 Password Lockout -
U2 Hidden Items U2 Submenu
U2 Hidden Items Enable -
U3 Units U3 Submenu
U3 Units Selection -
U4 Ovrspeed Test U4 Submenu
U4 Overspeed Test -
U5 Restore Dflts U5 Submenu
U5 Restore Motor Dflts -
U5 Restore Drive Dflts -
U5 Restore Utility Dflts -
U6 Motor Side Info U6 Submenu
U6 MS Type -
U6 MS Code Version -
U6 MS S/W Date -
U6 MS S/W Time -
U6 MS FPGA Version -
U6 MS Cube ID -
U7 Line Side Info U7 Submenu
U7 LS Type -
U7 LS Code Version -
U7 LS S/W Date -
U7 LS S/W Time -
U7 LS FPGA Version -
U7 LS Cube ID -
U8 Hex Monitor U8 Submenu
U8 Hex Monitor -
F1 Active Faults F1 Submenu
F1 Display Active Faults -
F1 Reset Active Faults -
F2 Faults History F2 Submenu
F2 Display Fault History -
F2 Clear Fault History -
F2 Display Fault Counters -
9