Filter
Top Products
Index
Lab-NB User Manual Index-4 © National Instruments Corporation
GATA1, 4-9
IBFA, 4-60, 4-64
IBFB, 4-60
INT, 4-33
INTE1, 4-64
INTE2, 4-64
INTEA, 4-60, 4-62
INTEB, 4-60, 4-62
INTRA, 4-60, 4-62, 4-64
INTRB, 4-60, 4-62
I/O, 4-60, 4-62, 4-64
MA<2..0>, 4-7 to 4-8
OBFA*, 4-62, 4-64
OBFB*, 4-62
OVERFLOW, 4-9, 4-38, 4-42, 4-45,
4-48, 4-51
OVERRUN, 4-9, 4-42, 4-45, 4-48, 4-51
PAINTEN, 4-31
*PAINTEN, 4-33
PBINTEN, 4-31
*PBINTEN, 4-33
PRETRIG, 2-17, 2-19, 4-7, 4-45, 4-46,
4-47, 4-49
SCANEN, 4-7, 4-40, 4-47, 4-49, 4-51
to 4-52
TBSEL, 4-6, 4-39
TIMERUP, 4-33, 4-55
TMRINTCLR, 4-55
TMRINTEN, 2-19, 4-31 to 4-32
*TMRINTEN, 4-33
TMRINTUP, 2-20
TMRWGEN, 2-19, 3-8
TMRWGN0, 4-14, 4-52, 4-54
TMRWGN1, 4-14, 4-52, 4-54
TWOSCMP, 4-8
TWOSDA, 4-43
TWOSDA0, 4-14
TWOSDA1, 4-14
block diagram of Lab-NB, 3-1
board configuration. See configuration of
jumpers.
C
cabling for Lab-NB, 1-4 to 1-5
calibration
analog input, 5-3 to 5-5
bipolar input calibration procedure,
5-4 to 5-5
gain calibration, 5-4 to 5-5
offset calibration, 5-4
board configuration, 5-4
unipolar input calibration procedure
gain calibration, 5-5
offset calibration, 5-5
analog output, 5-5 to 5-8
bipolar output calibration procedure,
5-6 to 5-7
adjusting analog output gain, 5-6
adjusting analog output
offset, 5-6
board configuration, 5-6
unipolar output calibration procedure
adjusting analog output gain, 5-8
adjusting analog output offset,
5-7 to 5-8
equipment requirements, 5-1
trimpots, 5-2
location diagram, 5-2
circular buffer, 4-46
CLK signal
counter block diagram, 3-11
general-purpose timing, 2-21 to 2-24
specifications and ratings, 2-23
timing requirements (figure), 2-24
CLKB1 signal (table), 2-7
CLKB2 signal (table), 2-7
Configuration EPROM, 4-35
configuration of jumpers. See also signal
connections.
analog output configuration
bipolar output selection, 2-3 to 2-4
unipolar input selection, 2-4
factory default settings (table), 2-3
jumpers on Lab-NB, 2-1
parts locator diagram, 2-2
control words
format
with control-word flag set to 0
(figure), 4-57
with control-word flag set to 1
(figure), 4-57
mode 0 I/O configurations (table), 4-58
mode 1 strobed input, 4-59
mode 1 strobed output, 4-61
mode 2, 4-63