Filter
Top Products
Index
AT-MIO/AI E Series User Manual I -6
National Instruments Corporation
frequently asked questions. See questions
about AT E series boards.
FTP support, D-1
fuse, 4-6
G
general-purpose timing signal
connections, 4-46 to 4-57
FREQ_OUT signal, 4-52
GPCTR0_GATE signal, 4-47
GPCTR0_OUT signal, 4-47 to 4-48
GPCTR0_SOURCE signal, 4-46
GPCTR0_UP_DOWN signal, 4-48
GPCTR1_GATE signal, 4-49 to 4-50
GPCTR1_OUT signal, 4-50
GPCTR1_SOURCE signal, 4-48 to 4-49
GPCTR1_UP_DOWN
signal, 4-51 to 4-52
GPCTR0_GATE signal, 4-47
GPCTR0_OUT signal
AT-MIO-16E-1, AT-MIO-16E-2 and
AT-MIO-64E-3 (table), 4-9
AT-MIO-16E-10 and AT-MIO-16DE-10
(table), 4-11
AT-MIO-16XE-10 and AT-AI-16XE-10
(table), 4-13
AT-MIO-16XE-50 (table), 4-15
description (table), 4-8
waveform generation timing
connections, 4-47 to 4-48
GPCTR0_SOURCE signal, 4-46
GPCTR0_UP_DOWN signal, 4-48
GPCTR1_GATE signal, 4-49 to 4-50
GPCTR1_OUT signal
AT-MIO-16E-1, AT-MIO-16E-2 and
AT-MIO-64E-3 (table), 4-9
AT-MIO-16E-10 and AT-MIO-16DE-10
(table), 4-11
AT-MIO-16XE-10 and AT-AI-16XE-10
(table), 4-12
AT-MIO-16XE-50 (table), 4-14
description (table), 4-7
waveform generation timing
connections, 4-50
GPCTR1_SOURCE signal, 4-48 to 4-49
GPCTR1_UP_DOWN signal, 4-51 to 4-52
ground-referenced signal sources
description, 4-18
differential connections, 4-21
single-ended connections (NRSE
configuration), 4-25
H
hardware installation, 2-1 to 2-2
hardware overview
analog input, 3-6 to 3-13
considerations for selecting input
ranges, 3-10
dither, 3-11 to 3-12
input modes, 3-6 to 3-7
input polarity and range, 3-7 to 3-10
multiple-channel scanning
considerations, 3-12 to 3-13
analog output, 3-14 to 3-15
output polarity
selection, 3-14 to 3-15
reference selection, 3-14
reglitch selection, 3-15
analog trigger, 3-15 to 3-18
block diagram, 3-16
AT-AI-16XE-10 block diagram, 3-5
AT-MIO-16E-1 and AT-MIO-16E-2
block diagram, 3-1
AT-MIO-16E-10 and AT-MIO-16DE-10
block diagram, 3-3
AT-MIO-16XE-10 block diagram, 3-4
AT-MIO-16XE-50 block diagram, 3-6
AT-MIO-64E-3 block diagram, 3-2
digital I/O, 3-19
timing signal routing, 3-19 to 3-22
board and RTSI clocks, 3-21
programmable function
inputs, 3-20 to 3-21
RTSI triggers, 3-21 to 3-22