Filter
Top Products
Copying_ 61
When you make a reduced copy, black lines may appear at the
bottom of your copy.
CHANGING THE DEFAULT COPY SETTINGS
The copy options, including darkness, original type, copy size, collation and
number of copies, can be set to those most frequently used. When you copy
a document, the default settings are used unless they have been changed
by using the corresponding buttons on the control panel.
1. Pres
s (Copy) on the control panel.
2. Press Menu on the control panel.
3. Pres
s the left/right arrow until Copy Setup appears and press OK.
4. Pres
s the left/right arrow until Change Default appears and press OK.
5. Pres
s the left/right arrow until the setup option you want appears and
press OK.
6. Press the left/right arrow until the setting you want appears and press
OK.
7. R
epeat steps 5 through 6, as needed.
8. Pres
s Stop/Clear to return to ready mode.
While you are setting copy options, pressing Stop/Clear cancels the
changed settings and restores the defaults.
USING SPECIAL COPY FEATURES
You can use the following copy features:
ID card copying
Your machine can print 2-sided originals on one sheet of A4-, Letter-,
Legal-, Folio-, Executive-, B5, A5, or A6-sized paper.
The machine prints one side of the original on the upper half of the paper
and the other side on the lower half without reducing the size of the original.
This feature is helpful for copying a small-sized item, such as a business
card.
• This copy feature is available only when you place originals on the
scanner glass.
• The size of the 2-sided originals should be smaller than A5, if not,
some of it won’t be copied.
1. Press ID Copy on the control panel.
2. Place Front Side and Press [Start] ap
pears on the display.
3. Pla
ce the front side of an original facing down on the scanner glass
where arrows indicate as shown, and close the scanner lid.
4. Press OK on the control panel.
Your machine begins scanning the front side and shows P
lace Back
Side and Press [Start].
5. T
urn the original over and place it on the scanner glass, where arrows
indicate as shown then, close the scanner lid.
6. Press OK on the control panel to begin copying.
• If the original is larger than the printable area, some portions may
not be printed.
• If you don’t press the OK button, only the front side will be copied.
• If you press St
op/Clear, the machine cancles the copy job and
returns to ready mode.
2-up or 4-up copying (N-up)
The machine reduces the size of the original images and prints 2 or 4 pages
onto one sheet of paper.
1 2
1 2
3 4
1. Press (Copy) on the control panel.
2. Press Menu on the control panel.
3. Pr
ess the left/right arrow until Copy Feature appears and press OK.
4. Pr
ess the left/right arrow until Layout appears and press OK.
5. Pr
ess the left/right arrow until 2-Up or 4-Up appears and press OK.
6. W
hen Yes appears, press OK.
7. Pr
ess Start on the control panel to begin copying.
You cannot adjust the copy size using Reduce/Enlarge for the N-Up
feature.
Poster copying
Your original will be divided into 9 portions. You can paste the printed pages
together to make one poster-sized document.
This copy feature is available only when you place originals on the scanner
glass.
1. Press (Copy) on the control panel.
2. Press Menu on the control panel.
3. Pr
ess the left/right arrow until Copy Feature appears and press OK.
4. Pr
ess the left/right arrow until Layout appears and press OK.
5. Pr
ess the left/right arrow until Poster Copy appears and press OK.
6. Pr
ess Stop/Clear to return to ready mode.
7. Pr
ess Start on the control panel to begin copying.
Your original is divided into 9 portions. Each portion is scanned and