Filter
Top Products
6. PROGRAMMING OPERATIONS EO1-11152
6.6 PLU Table Programming (Submode 4)
6-20
Key Operation: Mode Lock: SET, Enter 3 and depress the [X] key.
1 [DP#] (Department 1)
1 [ST] (Address 1: Link Group)
0101 [#] (Major Group: 01,
Minor Group: 01)
2 [ST] (Address 2: Dept. Name)
506 [#] (V)
405 [#] (E)
407 [#] (G)
405 [#] (E)
504 [#] (T)
401 [#] (A)
402 [#] (B)
412 [#] (L)
405 [#] (E)
[ST] (to end Dept. Name setting)
3 [ST] (Address 3: Preset Price)
[#] (Open-price department)
4 [ST] (Address 4: Status Code 1)
5 [#] (Scale-allowed status)
5 [ST] (Address 5: Status Code 2)
0 [#] (No ON-status)
6 [ST] (Address 6: TaxStatus)
1 [#] (Tax 1)
7 [ST] (Address 7: High Amount
Limit)
10000 [#] (100.00)
8 [ST] (Address 8: Low Amount Limit)
10 [#] (0.10)
9 [ST] (Address 9: Sub-link Dept. Code)
0 [#] (No Sub-link Dept.)
15 [DP#] (Department 15)
1 [ST] (Address 1: Link Group)
0 [#] (No linked group)
3 [ST] (Address 3: Preset Price)
[#] (Open-price department)
4 [ST] (Address 4: Status Code 1)
3 [#] (Negative Dept. status)
5 [ST] (Address 5: Status Code 2)
0 [#] (No ON-status)
6 [ST] (Address 6: Tax Status)
0 [#] (Non-taxable)
7 [ST] (Address 7: High Amount Limit)
0 [#] (No limit)
8 [ST] (Address 8: Low Amount Limit)
0 [#] (No limit)
9 [ST] (Address 9: Sub-link Dept. Code)
0 [#] (No Sub-link Dept.)
[AT/TL] (to complete this submode)
NOTES: 1. In this example, the Address Designation feature is not used.
2. In this example, the Dept. Code is entered through the [DP#]
key; however, it can be replaced by depressing the actual
Dept Code-preset key instead, if that Department Key exists
on the keyboard (which is applicable to the Ordinary Keyboard
Type). Only to open the memory of a department:
3 [X] |Department Code
| [DP#] [AT/TL]
3. If the Dept. Code is sequential from the previous one, the Dept. Code before the [DP#] can be
omitted.
4. If the Address No. is sequential from the previous one, the Address No. + [ST] may be omitted.
(In the above example, all address entries are not omitted for an easy understanding of the sample
operation.)
5. For the name setting (Address 2), the CHARACTER CODE ENTRY method has been used. But
the DIRECT CHARACTER ENTRY method is also possible if you have any of FLAT KEYBOARD
and PLU KEYBOARD (PK-2). Refer to Section 6.2 Character Entries.
6.6.2 Deletion
After Department and PLU Daily and GT Resets
Mode Lock: SET
Individual Department Deletion
[DEPT]
3 [X] [ITEM CORR] [AT/TL]
or |Department Code
| [DP#]
[VOID]
All Department Deletion
3 [X] [ITEM CORR] [ALL VOID] [AT/TL]
or
[VOID]
TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437
Open 8:00am to 7:00pm
Closed: every Wednesday
08-22-2003 FRI #0
P03
01
DP
01
#01 0101
#02 VEGETABLE
#03
#04 5
#05 0
#06 1
#07 100.00
#08 0.10
#09 00
15
DP
15
#01 0000
#03
#04 3
#05 0
#06 1
#07 0.00
#08 0.00
#09 00
0028 14:39TM
OPERATION
CONDITION
Repeatable for other departments to be deleted.