Filter
Top Products
98
Algorithm List
HiMid Q (High Middle Q) 0.3–16.0 Sets the width of the area around the High middle
frequency that will be affected by the gain settings.
High Gain (High Gain) -12– +12 dB Sets the boost/cut amount in the High frequency band.
High Freq (High Frequency) 1.40–20.0 kHz Sets the center frequency in the High frequency band.
High Q (High Q) 0.3–16.0 Sets the width of the area around the High frequency that
will be affected by the gain settings. *1
Hi Type (High Type) Shlv, Peak Sets the type of the High frequency band equalizer (Shlving
type or peaking type).
Level (Level) -24– +12 dB Sets the overall volume after passing through the equalizer.
BCut (Bass Cut Filter): Cuts off undesired low frequency band sounds such as pop noise.
Sw (Switch) On, Off Turns the bass cut filter on or off.
Freq (Frequency) Thru, 20 - 2000 Hz Sets the frequency for cutting off undesired low frequency
band sounds such as pop noise.
Enh (Enhancer): Accentuates the sound and push the sound forward.
Sw (Switch) On, Off Turns the enhancer on or off.
Sens (Sensitivity) 0–100 Sets the degree of the enhancer effect desired.
Freq (Frequency) 1.00–10.0 kHz Sets the frequency at which the enhancer effect starts working.
MixLvl (Mix Level) -24– +12dB Set the amount of the enhancer sound to be added to the direct sound.
In (Input): Splits the direct sound into three frequency bands, that is, low, middle and High
frequency bands.
InGain (Input Gain) -24– +12dB Sets the overall volume before entering expander/compressor.
D-Time (Detect Time) 0–10 ms Sets the length of delay to add to the direct sound input.
Split Point Low (Low Split Point) 20–800 Hz Sets the frequency at which the direct sound is split into three bands (on the
low frequency band side).
Split Point High (High Split Point) 1.60–16.0 kHz Sets the frequency at which the direct sound is split into three bands (on the
High frequency band side).
Exp (Expander): Expands the dynamic range at a certain ratio.
Sw (Switch) On, Off Turns the expander on or off.
Low Thre (Low Threshold) -80–0 dB
Sets the volume at which the expander for the low frequency band starts working
.
Low Ratio (Low Raito) 1:1.0–1:16, 1:INF Sets the ratio at which the output in the low frequency band is increased
when the input level has exceeded below the low threshold level.
Low Atck (Low Attack) 0–100 ms Sets the time until when the low frequency band expander starts working
after the input level dropps below the low threshold level.
Low Rel (Low Release) 50 ms–5.000 s Sets the time until when the High frequency band expander stops working
after the input level exceeds the low threshold level.
Mid Thre (Middle Threshold) -80–0 dB
Sets the volume at which the expander for the middle frequency band starts
working
.
Mid Ratio (Middle Ratio) 1:1.0–1:16, 1:INF Sets the ratio at which the output in the middle frequency band is increased
when the input level has exceeded below the middle threshold level.
Mid Atck (Middle Attack) 0–100 ms Sets the time until when the middle frequency band expander starts working
after the input level dropps below the middle threshold level.
Mid Rel (Middle Release) 50 ms–5.000 s Sets the time until when the middle frequency band expander stops working
after the input level exceeds the middle threshold level.
High Thre (High Threshold) -80–0 dB
Sets the volume at which the expander for the High frequency band starts
working
.
High Ratio (High Ratio) 1:1.0–1:16, 1:INF Sets the ratio at which the output in the High frequency band is increased
when the input level has exceeded below the High threshold level.
High Atck (High Attack) 0–100 ms Sets the time until when the High frequency band expander starts working
after the input level dropps below the High threshold level.
High Rel (High Release) 50 ms–5.000 s Sets the time until when the High frequency band expander stops working
after the input level exceeds the High threshold level.
2400_app_e.book 98 ページ ２００５年４月２８日 木曜日 午後１時１４分