Filter
Top Products
28 IBM Sterling Connect:Direct for i5/OS User’s Guide
The following TOSYSOPTS parameters are valid for TYPE(SPLF) files:
DEV(*JOB|*SYSVAL|device-name) specifies the name of the printer device description.
DEVTYPE(*IPDS|*SCS)|*USERASCII specifies the type of data stream created for a printer
file from the data received.
PAGESIZE(page-length page-width) specifies the length and width of the page used by the
printer. This parameter overrides the FORMTYPE parameter.
LPI(3|4|6|7.5|8|9) specifies the line space setting (lines per inch) on the printer.
CPI(5|10|12|13.3|15|16.7|18|20) specifies the printer character density, in characters per inch, for
the printer.
OVRFLW(overflow-line-number) specifies the line number on the page where overflow to a
new page begins. The value specified must not exceed the form length specified for PAGESIZE.
FOLD(*NO|*YES) specifies whether entire records are printed when the record length exceeds
the form width.
RPLUNPRT(*YES ‘replacement-character’|*NO) specifies whether unprintable characters
are replaced with printable characters when printed. It also specifies the replacement character.
ALIGN(*NO|*YES) specifies whether the page must be aligned in the printer before printing is
started.
CTLCHAR(*NONE|*FCFC) specifies whether the data contains printer control characters.
CHLVAL(*NORMAL| (channel#1 line#1) ... (channel#12 line#12)) specifies the list of
channel numbers with their assigned line numbers. Note that CTLCHAR(*FCFC) must be
specified as a SYSOPTS parameter for this to be a valid parameter.
FORMFEED(*DEVD|*CONT|*CUT|*AUTOCUT) specifies the form feed attachments used
by the printer (4214, 5219, and 5553 printers only).
PRTQLTY(*STD|*DRAFT|*DEVD|*NLQ) specifies the quality of print produced.
DRAWER(1|2|3|*E1) specifies the source drawer to be used when automatic cut-sheet feed
mode is used. FORMFEED(*AUTOCUT) must be specified as a SYSOPTS parameter for this to
be a valid parameter.
FONT(*CPI|*DEVD|font-identifier) specifies the font identifier to be used for the spooled
output file.
CHRID(*DEVD|*SYSVAL| graphic-character-set code-page) specifies the character
identifier to be used for the spooled output file. This parameter allows you to print data with
different character identifier coding.
PAGRTT(*DEVD|*COR|0|90|180|270) specifies the degree of rotation (clockwise from the
edge of the paper first loaded into the printer) of text on each page printed. 0|90|180|270 indicates
the specific angle of rotation.
PRTTXT(‘print-text’) specifies a line of text to be printed at the bottom of each page printed.
Up to 30 characters enclosed in single quotes is specified.
JUSTIFY(0|50|100) controls the print positions of the characters on the page (in the spooled file)
so the right margin is regular.
DUPLEX(*NO|*YES|*TUMBLE) specifies whether the spooled output file is printed on one or
both sides of the paper.
SPOOL(*YES|*NO) specifies whether the data is sent to a spooled file prior to printing.
OUTQ(*JOB|*DEV|library-name/output-queue- name) specifies the output queue for the
spooled output file created. This parameter is valid only when SPOOL(*YES).
FORMTYPE(form-type) specifies the type of form to use in the printer when the spooled file is
printed. A form-type identifier is user-defined and is no longer than 10 characters. The
PAGESIZE parameter overrides this parameter.