Filter
Top Products
RESTRICTED USE ONLY Fargo Electronics, Inc.
DTC400/DTC300/DTC300M Card Printer Service Manual (Rev. 1.3)
16-2
dimension boxes, 6-95
DIP switches (Dual In-line Package Switches), 15-4
Direct-to-Card (DTC) Printing, 15-5
D
isable Printing option, 6-28, 6-40
Disables Magnetic Verification, 5-55
disk cleanup utility, 5-5
Dither, 15-5
DMA (Direct Memory Access), 15-3
D
ongle, 15-5
Dot, 15-5
Dot pitch, 15-5
Download, 15-5
DPI (Dot Per Inch), 15-5
DRAM (Dynamic Random Access Memory), 15-5
Driver, 15-5
DTC400/DTC300/DTC300M Card Printer, 9-1
Duplex Printing, 15-5
Dwell Time, 15-6
Dye Migration, 15-6
Dye-Sub Intensity setting, 5-45
Dye-Sublimation, 2-8, 15-6
Dye-Sublimation Cyan Panel, 2-10
Dye-Sublimation Magenta Panel, 2-10
Dye-Sublimation Yellow Panel, 2-10
Dye-Sublimation-Only Print Ribbons, 2-12
E
E-card, 15-6
E-card Docking Station, 15-6
ECP Mode (Enhanced Capabilities Port Mode), 15-6
Edge-to-Edge, 15-6
EE Memory, 15-6
EEPROM (Electrically Erasable Programmable Read
Only Memory), 15-6
embedded contaminants, 2-14, 5-42
Emissions Standards, 2-3
EN 60950-1
2001, 2-2
Enable MLE Support checkbox, 6-56
Encoder (smart card), 15-6
Encoder (wheel), 15-7
encrypted secure code, 3-1
End Sentinel (ES)., 6-61
Engine, 15-7
EOF (End Of Form), 15-7
EPP (Enhanced Parallel Port), 15-7
EPROM (Electronically Programmable Read Only
Memory), 15-7
EPROM version number, 5-54, 5-56
Escape sequence, 15-7
ESD, 1-2, 6-4, 6-5, 7-2, 8-4, 10-1
ESD (ElectroStatic Discharge), 15-7
Ethernet, 15-7
excessive resin printing problems, 5-48
exposed to static electrical discharges, 7-3
F
Fargo Secure Print Security Suite, 3-1
Fargo Technical Support, 13-1
Fargo Technical Support via the Web, 13-1
FCC, 2-2
feed card into encoder, 5-5
Field Separator (FS), 6-61
F
ilm, 15-7
Firmware, 15-7
five (5) applications, 3-2
Flash Memory, 15-8
Flipper Table Module, 2-15
F
ont, 15-8
For Overlay Only, 6-70
For Print and Overlay, 6-70
FPGA (Field Programmable Gate Array), 15-8
Front and Back radio buttons, 2-15
Front Cover, 2-9
Frontside and Backside options
K Panel Resin, 6-87, 6-88, 6-89
Overlay / Print Area, 6-65
Full bleed, 15-8
Full Card option, 6-68, 6-91
G
Gamma, 15-8
Glossy / Matte, 15-8
Glossy PVC, 15-8
Graphical Device Interface (GDI), 15-8
Gray Scale, 15-8
H
Halftoning, 15-8
Hard Drive, 15-9
hard Drive space
adequate or inadequate, 5-5
HDP (High Definition Printing™), 15-9
Head, 15-9
Headlift Motor Assembly, 8-63, 8-65, 8-66
Headlift Motors, 5-33
Headlift Sensors, 5-33
Heat Seal, 15-9
Heat sink, 15-9
HiCo (High Coercivity), 15-9
High Coercivity Magnetic Head Assembly Replacement,
8-75
high-resolution, 24-bit color images, 5-53
Horizontal adjustment, 6-47
HTML (HyperText Markup Language), 15-9
HTTP (HyperText Transfer Protocol), 15-9
Humidity, 2-4
I
IC (Integrated Circuit), 15-9
ID (Identification), 15-9
ID format, 6-23, 6-36
Identification Card sample, 6-95
IEEE 1284 (Institute of Electrical and Electronics
Engineers 1284), 15-10
Image, 15-10
Image Color tab, 6-21, 6-41
Image Darkness option, 6-106
Image Placement, 5-51, 5-52