Filter
Top Products
User Command Specifications 10. Error List
1 10. Error List
(1)(2)(3)(4)
2
e
○○○○ Send the correct command.
4e ○○○○ Send in the correct command format.
8e
○○○○
i
○○○
i
○○○
e ○○○○
e ○○○
e ○○○
e ○○○
e
○○○○
i ○○○○
i ○○○○
i
○ ○ ○
i
○ ○ ○
16 e
○○○○
e
○○○○
e
○○○
18 i
○○○
※ The error code is expressed as a four-digit hexadecimal character string. ‘X’ is a number from ‘0’ to ‘9’ or letter from ‘A’ to ‘F’.
※
※ Given below is the correspondence between the numbers (1) to (4) in the "Errors supported by model" column and the models concerned.
(1) SX50
(2) SX6
(3) SX60
(4) X600
The zoom lens is now being driven. Wait until the zoom lens drive stops.
10 –
BUSY (FOCUS) The focus lens is now being driven.
17
BUSY (INTERNAL_PROCESS) Heavy processing is in progress.
INVALID_VALUE
Numerical parameters are invalid or
outside the range.
1003 IP conversion cannot be performed.
15 –
BUSY (FOCUS)
○○○○
Command is invalid (undefined).
Communication sequence error
Wait until the response is received to send
the command.
Remedy
0002
0801
0802
INVALID_COMMAND
000B JOB_TIMEOUT
0004 INVALID_FORMAT
F001
BUSY (ZOOM)
USER_COMMAND_VERSION_IS_UPDATED
Change to the correct resolution of the
input signal.
The input signal resolution is not correct.
1002 e NO_LOGO_CAPTURED
Change to the correct input signal.
203X e INVALID_RESOLUTION (***)
Register the user image.
INVALID_PARAMETERe000A7
E0XX12 e
9
11
F005
F002
F004
–
6 – i BUSY
Wait until the processing is completed.
Resend the command.
There is no signal input.
Resend the command.
Signal setting (detection) is in progress.
Input the signal.
A communication protocol violation
occurred in the projector.
Eliminate the cause of the error, and
resend the command.
An error occurred in AUTOSETEXE=SCRN.
Change the input signal.
Use the TERMINAL command to set the
terminal to input, and then select the input
again.
The focus lens is now being driven.
The input cannot be selected since the
terminal is set to output.
Processing cannot be executed since the
user image is not registered.
Wait until the focus lens drive stops.
The zoom lens is now being driven. Wait until the zoom lens drive stops.
Use the RANGE command to obtain the
parameter range, and then use a
parameter within the range.
Switch the mode using the REMOTE or
LOCAL command.
An error occurred in AUTOSETEXE=VKS.
Mode switching or processing inside the
projector is underway.
Wait until the power supply state changes
to “ON”, “OFF”, or “PMM”.
Resend the command.
Use GET COMVER to obtain the latest
user command version.
The user command version is being updated.
The command format is incorrect.
SX50 internal processing has timed out.
Wait until the focus lens drive stops.
1 0001 e BAD_SEQUENCE
3 0003 e
1006
13
e
1005
1001
e
w
NOW_BLANK
AUTOSETEXE=FOCUS or SCRN cannot
be executed since BLANK is ON.
After setting BLANK to ON, resend the
command.
○○
○
NO_SIGNAL
BUSY (NOW_SETTING)
COMMUNICATION_ERROR
○
10. Error List
Error
Item
Code
TYPE
Error character strings
Errors
supported by
model
The designated command cannot be
executed in this mode.
INVALID_MODE
○○
○
○○○○
○○○
○○○
○
○
○
○○○○
○○○
○
○
○○
○○
SYSTEM (SCREEN_COLOR)
○
SYSTEM (UNKNOWN) An internal error occurred.
SYSTEM (FOCUS)
An error occurred in AUTOSETEXE=FOCUS.
SYSTEM (AUTO_KEYSTONE)
○
– INPUT_NOT_FOUND
The input was not switched since no input signal
was found with AUTOSETEXE=INPUT.
○
INVALID_SOURCE (****)e200X
○○ ○
There is no action to be taken since the
status has been notified.
Use the POWER ON command to turn on
the power.
Power is not being supplied.
○
Use the correct parameter(s).
The parameter (type) is invalid
(undefined).This includes the case when
the number of parameters is incorrect.
○
This cannot be executed with the current
input source.
The current input source is indicated in
parentheses.
Change the input source.
NOT_POWER_SUPPLIED5 0005 e
e201X
14
2010
INVALID_SIGNAL (****)
This cannot be executed with the current
input signal.
The current input signal is indicated in
parentheses.
BUSY (ZOOM)
Preparing to switch to power management
standby.
○○○
BUSY
(POWER_MANAGEMENT_READY)
i
IP_NOT_AVAILABLE
○
TERMINAL_OUTe
Set DPON to ON when PMM is not OFF.
DPON cannot be set to ON when PMM is
OFF.
○○○
POWER_MANEGEMENT_OFF
Errors with the newer item numbers have higher priority. (When there is more than one error, the highest level error is returned. However, error priority
is the same within the same item number.)
1004
Set DPON to OFF.
PMM cannot be set to OFF when DPON is
ON.
○○○
DIRECT_POWER_ON
PAGE 177