Filter
Top Products
Pacific Research Solutions RI-300e User Manual
Page 151
S-Cmd Command Description
and Data Format
Read Back
Syntax
Command
Syntax
Factory
Setting
Stored
Location
14 User and S-Cmd control CTCSS/DCS tone panel decode
enable
Panel 0 = Both, 1 = User commands, 2 = S-Commands
Mode 0 = Disable (off), 1 = Enable (on)
14 [Panel] 14 [Panel] [Mode] 0
Off
RAM
EEPROM
15 User command group decode enable
Group = 1 to 8, 0 = All
Mode 0 = Disable (off), 1 = Enable (on)
15 [Group] 15 [Group] [Mode] Group 1
On
Group 2-4
Off
RAM
EEPROM
16 DTMF Decode Inter digit time
Time = 1 to 99 in 1/10 seconds increments
16 16 [Time] 35
3.5 Sec.
RAM
EEPROM
17 DTMF Decode Mute time
Time = 0 to 99 in 1/10 seconds increments, 0 = No mute
17 17 [Time] 25
2.5 Sec.
RAM
EEPROM
18 DTMF Mute control
Mute 0 = All, 1 = Repeater, 2 = Auxiliary, 3 = Telephone,
4-11 = Auxiliary inputs 1-8
Mode 0 = Disable (off), 1 = Enable (on)
18 [Mute] 18 [Mute] [Mode] 0 = All
1 = on
RAM
EEPROM
19 Resend DTMF
Location 0 = Read back only, 1 = Repeater,
2 = Auxiliary, 3 = Telephone
Digits = 0 to 9, A, B, D, *, # (32 digits max.)
19 0 19 [Location]
[Digits]
N/A N/A
20 Tone Panel CTCSS / DCS decode enable
Panel 0 = All, 1 = Repeater, 2 = User Commands,
3 = System-Commands, 4 = Auxiliary, 5 = Telephone,
6 = User programmable (Dial Click)
Tone = 001 to 154 decode tone number, 000 = All
Mode 0 = Disable (off), 1 = Enable (on)
20 [Panel]
[Tone]
20 [Panel] [Tone]
[Mode]
All 013
100.0 Hz
on
RAM
EEPROM
21 Tone Panel CTCSS / DCS master tone and cross encode
Encode Tone = 0 to 154 tone number, 0 = Disable
Decode Tone = 0 to 154 tone number, 0 = All, <Optional>
21 *
<Encode
Tone>
21 [Encode Tone]
<Decode Tone>
100.0 Hz
RAM
EEPROM
22 Tone Panel CTCSS / DCS encode mode.
Mode 0 = Off, 1 = Encode master tone all the time,
2 = Regen decode tone (allow change),
3 = Regen master tone/cross encode tone (allow change),
4 = Regen decode tone (priority user),
5 = Regen master tone/cross encode tone (priority user),
6 = Regen decode tone (only when active),
7 = Regen master tone/cross encode (only when active)
22 22 [Mode] 2
Regen
RAM
EEPROM
23 External source CTCSS / DCS encode tone
Source 0 =
Direct trigger
, 1 = ID, 2 = Aux in,
3 = Telephone ring, 4 = Local microphone
Tone 0 = No Tone, 1 to 154 = Tone number,
155 = Last Encode Tone, 156 = Master Tone,
157 = Aux source tone
23 [Source] 23 [Source] [Tone] 0
Default
RAM
EEPROM
24 CTCSS and DCS encode level
Encoder 0 = CTCSS, 1 = DCS
Adj. = 0 to 63 or * up one count, # down one count
24 [Encoder] 24 [Encoder] [Adj] 31
RAM
EEPROM
25 DCS TX and RX data polarity control
0 = TX, 1 = RX,
Pol 0 = Non-inverted, 1 = Inverted
25 [TX/RX] 25 [TX/RX] [Pol] TX = 0
RX = 0
RAM
EEPROM
26 CTCSS / DCS Total air-time
Tone = 0 to 154 tone number, 0 = All
Time = 0 to 59,999 Minutes
26 [Tone] 26 [Tone] [Time] All Tones=
0
EEPROM