Filter
Top Products
Pacific Research Solutions RI-300e User Manual
Page 155
S-Cmd Command Description
and Data Format
Read Back
Syntax
Command
Syntax
Factory
Setting
Stored
Location
69 Exit system command mode
Save 0 = Exit with out saving changes to EEPROM,
1 = Save to EEPROM and exit S-Cmd mode
Save only affects command stored locations that are in
bold & italic.
N/A 69 [Save] N/A N/A
70 Telephone outgoing call mod
Mode, 0 = Disable out going calls, 1 = Half duplex,
2 = Duplex, 3 = Mute talk back, half duplex,
4 = Mute talk back, half duplex with cover tone
5 = Monitor repeater receiver
6 = Link over telephone line
70 70 [Mode] 1
Half
Duplex
RAM
EEPROM
71 Telephone incoming call mode
Mode, 0 = Disable, 1 = Delay - On Hook - Ring TX
2 = Delay - Off Hook- Ring TX
3 = Delay - Off Hook - Ring PW required to ring TX
4 = Delay - Off Hook Ring PW, tone # and optional DTMF
string to ring TX (Tone and DTMF used during ring),
5 = Auto Answer after ring delay,
6 = Delay - Off Hook - Group 8 User Commands
71 71 [Mode] 2
RAM
EEPROM
72 Telephone CTCSS/DCS tone panel enable
Mode 0 = Disable (off), 1 = Enable (on)
72 72 [Mode] 0
COS
RAM
EEPROM
73 Telephone incoming call control time-out
Time = 1 to 150 in 1/10 minutes increments,
0 = no time-out
73 73 [Time] 3.0
Minutes
RAM
EEPROM
74 Telephone incoming call ring command and PW time-out
Time = 1 to 120 seconds
74 74 [Time] 30
Seconds
RAM
EEPROM
75 Telephone ring delay, rings before controller responds
Ring = 0 to 15
75 75 [Ring] 2
Rings
RAM
EEPROM
76 Telephone TX ring limit
Ring = 0 to 31, 0 = no limit
76 76 [Ring] 8
Rings
RAM
EEPROM
77 Telephone off hook time-out
Time = 0 to 240 minutes, 0 = no time-out
77 77 [Time] 10
Minutes
RAM
EEPROM
78 Telephone, no activity on RX time-out
Time = 0 to 240 seconds, 0 = no time-out
78 78 [Time] 60
Seconds
RAM
EEPROM
79 Telephone AGC level set
Level = 0 to 7 (0 = AGC off)
79 79 [Level] 4
RAM
EEPROM
80 Flash hook switch, used for call waiting and hold N/A 80 N/A N/A
81 Telephone dial tone/pulse select
Dial 0 = tone, 1 = pulse
81 81 [Dial] 0
Tone
RAM
EEPROM
82 Telephone on/off hook, access codes and account codes
Code = 1 to 8 off hook than code, 0 = on hook,
9 = Answer ringing telephone
N/A 82 [Code] N/A N/A
83 Edit telephone access and account codes
Type 0 = Access code, 1 = Account code
Code = 1 to 8 access and account code memory location
Number = 0 to 32 digits
83 * [Type]
[Code]
83 [Type] [Code]
[Number]
None EEPROM
84 Telephone number auto-dial
*xx to recall stored number when dialing
*00 to recall last number radial
Store = 00 to 99 memory location
Number = 0 to 16 digits (0-9, *, #, A = Pause)
84 xx to clear a memory location
84 * [Store] 84 [Store] [Number] None EEPROM
85 Set an Auto-Dial number for use in a macro
Auto Dial = 00 to 99 store position
85 85 [Auto Dial] N/A N/A
86 Telephone number accept table enable
Mode 0 = Disable (off), 1 = Enable (on)
86 86 [Mode] 0
Off
RAM
EEPROM