Filter
Top Products
Pacific Research Solutions RI-300e User Manual
Page 156
S-Cmd Command Description
and Data Format
Read Back
Syntax
Command
Syntax
Factory
Setting
Stored
Location
87 Edit telephone number accept table
Accept = 00 to 99 table entry
Number = 0 to 16 digits (0-9, * = Wild card)
87 * [Accept] 87 [Accept]
[Number]
None NV
RAM
88 Telephone number reject table enable
Mode 0 = Disable (off), 1 = Enable (on)
88 88 [Mode] 0
Off
RAM
EEPROM
89 Edit telephone number reject table
Reject = 00 to 99 table entry
Number = 0 to 16 digits (0-9, * = Wild card)
89 * [Reject] 89 [Reject]
[Number]
None NV
RAM
90 Wait for dial tone
Time = 0 to 99 in 1/10 seconds inc. (0 = Auto detect)
90 90 [Time] 50
5.0 Sec.
RAM
EEPROM
91 Set transmit and receive frequency
TX/RX 1 = Transmit, 2 = Receive
Freq = Frequency starting at 100s MHz (8 digits max)
TX Offset #1 = Minus, #2 = Simplex, #3 Plus <optional>
91 [TX/RX] 91 [TX/RX] [Freq]
<TX Offset>
N/A EEPROM
92 Set radio type
Mode 0 = Vertex VXR-500 Duplex, 1 Simplex,
2 = FTL connected to RBI-3, 3 = FTL radio interface
4 = Cactus Syntor remote interface
5 = Cactus Syntor radio interface
6 = RB-3 General purpose port
7 = VXR-5000 ACC General purpose port
8 = Doug Hall RBI-1 connected to PacRes RBI-3
9 = Doug Hall RBI-1 connected to VXR-5000 ACC
10 = Generic Data Radio connected to PacRes RBI-3
11 = Generic Data Radio connected to VXR-5000 ACC
92 92 [Mode] 0
VX-5000
RAM
EEPROM
93 Frequency limits and Offset
Limit 0 = Low, 1 = High, 2 = Offset
Limit Freq = Freq starting at 100s MHz (8 digits max)
Offset Freq = Freq starting at 1s MHz (4 digits max)
93 [Limit] 93 [Limit] [Freq] 0
&
99999999
No limits
RAM
EEPROM
94 Set programming channel frequency steps
Steps 0 = 5 KHz, 1 = 10 KHz, 2 = 12.5 KHz,
3 = 15 Khz, 4 = 20 Khz, 5 = 25 Khz, 6 = 50 KHz
94 94 [Step] 0
5.0 KHz
RAM
EEPROM
95 Frequency Increment and Decrement
Inc/Dec 0 = Decrement, 1 = Increment
95 95 [Inc/Dec] N/A N/A
96 Generic Data Radio and DHE RBI-1 Interface
Item 0 = User Function Bits
Data 1x – 8x = User Function Bit
Data x0 = Off, x1 = On
Item 1 = Radio Function
Data 1x = Rx, 2x = Tx, 3x = TSQ Encode,
4x = TSQ Decode, 5x = Scan, 6x = Squelch
7x = Power
Data x0 = Off, x1 = On
Item 2 = Receive Frequency and Offset
Data = Freq. starting at 100s MHz (8 digits max)
#1 = Minus, #2 = Simplex, #3 Plus, #4 Minus 20
Item 3 = TSQ (CTCSS) Select
Data = See table in Section 12, S-Cmd 96
Item 4 = Transmitter Power Level
Data 0 = Low, 1 = High, 2 = Mid
Item 5 = Memory Channel Recall
Data 0 = VFO, 1-20 = Memory channel number
Item 6 = Memory Channel Save
Data 1-20 = Memory channel number
Item 7 = Squelch Setting
Data 0-15 = Squelch level
96 [Item] 96 [Item] [Data] Item 0
0 (Low)
Item 1
0 (Off)
Item 2
0.0MHz
Item 3
1 (67.0Hz)
Item 4
0 (Low)
Item 5
0 (VFO)
Item 6
N/A
Item 7
0
RAM
EEPROM
97 Reserved 97 97
98 Reserved 98 98
99 User Scratch Pad
Variable = 00 – 99, Variable = 0 – 255, * (Inc) and # (Dec)
99 [Var] 99 [Var] [Value] All
0
RAM
EEPROM