Filter
Top Products
CHAPTER 4 Installation of Operating System and bundled software
4.3 Procedures to install Windows into internal HDD/SSD
53
following URL.
http://support.ts.fujitsu.com/
Note:
The driver/utility can be used in the PRIMEQUEST 2000 series though PRIMERGY is described in the
downloaded binary.
b. Double click the downloaded file and execute it.
The prompt screen of cmd.exe (black window) is displayed for a while and the file is extracted.
c. The window is closed automatically when the extraction is completed.
The downloaded file is uncompressed, and the folder or the file is created newly.
Remark
When the window is not closed even if displayed as [Complete] in the title bar of the window, click the [Close]
button and close the window.
d. Double-click the " elxocm-windows-x86-XXXXX.exe"(in case of x86, 32-bit OS) or "elxocm-windows-x64-
XXXXX.exe"(in case of x64, 64-bit OS) in the “FC_vXXXXXX" directory created in the decompression, and
execute it.
Remark
“XXXXX” shows the version number. Read it in different way properly.
2. Qlogic Converge Console (GUI/CLI) is installed in the following cases.
- When the Qlogic FC card is mounted.
And
- When Qlogic Converge Console (GUI/CLI) is not installed
The installation condition of Qlogic Converge Console (GUI) is determined by the presence of [Qlogic Corporation] –
[QCC GUI(localhost)] under the [start] menu – [all programs]
The installation condition of Qlogic Converge Console (CLI) is determined by the presence of [Qlogic Management
Suite] -[QConvergeConsole CLI] under the [start] menu – [all programs]
Note
In Windows Server 2012 or Windows Server 2012 R2, “the [start] menu – [all programs]“ should read “the [start]
menu – [all apps]“.
a. Driver/ Utility of MC-0JFC5X or MC-0JFC6X is downloaded from the following URL.
http://support.ts.fujitsu.com/
Note
Driver/Utility can be used by the PRIMEQUEST 2000 series though PRIMERGY is described in the
downloaded binary.
b. The downloaded file is executed by a double click.
The prompt window of cmd.exe (black window) is displayed for a while and the file is extracted.
c. The window closes automatically after the extraction is completed.
The download file is extracted and folder or file is newly created.
Remark
If the window does not close even if "Complete" is displayed on the title bar of the window then click the "Close"
button and close the window.
d. Double click and execute "QConvergeConsole_Installer_Windows_XXXXX.exe" in "QCC_vXXXXXX"
directory created by extraction.
Remark
"XXXX" shows the version number. Read properly.
3. When the installation is completed, reboot the partition.
4. Check the setting of management LAN.
The STP function of the port to be connected is turned OFF when the management LAN is used for communication
with MMB in the switching hub which supports the STP function.
5. Set the trap destination and Mail Sending destination through MMB.
Execute linkage with the operation management software only if necessary.
a. The [SNMP setting] is displayed on the MMB screen, and enable the SNMP.
b. The trap destination of SNMP is set through MMB.
See “6.5.2 Set up of SNMP”
6. Set the dump area.
Check whether there is sufficient free space in the hard disk before acquiring the memory dump. For details, see
(“11.4.4 Setting (Windows) of dump environment” of PRIMEQUEST 2000 series Administration Manual (C122-
E175EN).
7. Save the management information and configuration information.
For details, see “5.7 Saving management and configuration information”.
8. Set RAS support service.