Filter
Top Products
47 _Copying
3. Select the tray in Paper Supply.
4. Press the Advanced tab > Clone Copy.
5. Press On to activate this feature.
6. Press OK.
7. Press Start on the control panel to begin copying.
Book copying
Use this feature to copy a book. If the book is too thick, lift the scanner lid
until its hinges are engaged by the stopper and then close the scanner lid. If
the book or magazine is thicker than 30 mm(1.18 inches), start copying with
the scanner lid open.
This copy feature is available only when you place originals on the scanner
glass.
1. Place the originals face down on the scanner glass. (See "Loading
originals" on page 33.)
2. Press Copy from the Main screen.
3. Press the Advanced tab > Book Copy.
4. Select the binding option.
• Off: Disables this feature.
• Left Page: Prints left page of the book.
• Right Page: Prints right page of the book.
• Both Page: Prints both facing pages of the book.
5. Press OK.
6. Press Start on the control panel to begin copying.
Booklet copying
The machine automatically prints on one or both sides of the paper,
which are then folded to produce a booklet with all of the pages in
the correct sequence.
The machine will also reduce and correctly adjust the position of each
image to fit on the selected paper.
1. Place the originals face up in the DADF. Or place a single original face
down on the scanner glass. (See "Loading originals" on page 33.)
2. Press Copy from the Main screen.
3. Select the tray in Paper Supply.
4. Press the Advanced tab > Booklet.
5. Press On to use this feature, and select detailed settings for each
option.
• 1 Sided Original: Copies on one side of the paper.
• 2 Sided Original: Copies on both sides of the paper.
6. Press OK.
7. Press Start on the control panel to begin copying.
Cover copying
The machine automatically adds covers to your copied set using stock taken
from a different tray. Covers must be the same size and orientation as the
main body of the job.
1. Place the originals face up in the DADF. Or place a single original face
down on the scanner glass. (See "Loading originals" on page 33.)
2. Press Copy from the Main screen.
3. Select the tray in Paper Supply.
4. Press the Advanced tab > Covers.
5. Press On to use this feature, and select detailed settings for each
option.
• Position: Selects whether the cover will be placed at the front, back,
or both.
• Cover Sheet: Selects whether the cover will be 1 sided, 2 sided, or
blank paper.
• Paper Source: Select the paper tray, where the cover sheet is
loaded.
6. Press OK.
7. Press Start on the control panel to begin copying.
Transparency copying
When you prepare transparencies for presentations, use this feature to copy
the information.
1. Place the originals face up in the DADF. Or place a single original face
down on the scanner glass. (See "Loading originals" on page 33.)
2. Load the right-sized transparencies into the tray you have set.
3. Set the paper type to Transparency.
4. Press Copy from the Main screen.
5. Press the Advanced tab > Transparencies.
6. Select Transparencies option.
• No Separator: Does not place separator sheets between
transparencies.
• Blank Sheet: Places a blank sheet between transparencies.
• Printed Sheet: Places the same image on the divider sheets as
printed on the transparency.
7. Select media sources, in case you selected either Blank Sheet or
Printed Sheet.
This feature is available only when the options in the Basic tab are
selected as below;
- Duplex to 1 -> 1 Sided
- Reduce/Enlarge to Original(100%)
- Paper Supply to Tray.
To remove shadows of a book edge, press the Image tab > Erase
Edge > Book Center and Edges Erase.
This feature is possible only with A4, Letter, Legal, Folio, Oficio, JIS
B5, ISO B5, Executive, A5 and Statement sized paper.
Once you have set the Paper Supply option to Auto, you cannot use
this feature.
Before you start this special copy job, set the tray's Paper Types and
Paper Size to Transparency.(See "Setting the paper size and type" on
page 40.)