Filter
Top Products
X6$ = Port timeout (10‑sec. increments) 1 (= 10 seconds) – 65000 (default is 30 = 300 seconds = 5 minutes)
X6% = SMNP port number 00000 (= disable) – nnnnn. Default = 00161. Leading zeroes are not necessary for entry.
X6^ =
SNMP contact name and location
Up to 64 alphanumeric characters. Default = Not•Specified.
X6& = SNMP community name Up to 64 alphanumeric characters.
Default = public (for read community) or private (for read‑write community).
X6* = Trap target 1 – 3
X6( = SNMP trap version 2 or 3, or 0 = empty (default) if no target set
X7)
= SNMP target 1 through 3 70 – 72. 70 = SNMP target 1, ... 72 = target 3
Command and Response Table for IP- and SNMP-Specific SIS Commands
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
IP setup commands
Set matrix name
EX4)
CN
}
Ipn•
X4)]
Read matrix name (location)
E
CN
} X4)]
Reset matrix name to factory default
E
•CN
}
Ipn•
X4)]
“FOX-Matrix-3 (7)‑” plus the last
3 pairs of the MAC address.
Set time and date
E
X4@
CT
}
Ipt
X4@]
Read time and date
E
CT
} X4#]
Set GMT offset
EX4$
CZ
}
Ipz
X4$]
In the command, the divider between
hours and minutes can be either a
colon or a period. In the response, the
divider is a colon.
Example:
E
8.3CZ
}
Ipz+08:30
]
8.3 = 8:30
Read GMT offset
E
CZ
} X4$]
Set Daylight Saving Time
EX4%
CX
} X4%]
Read Daylight Savings Time
E
CX
} X4%]
Set IP address
EX4^
CI
}
Ipi
X4^]
Read IP address
E
CI
} X4^]
Read hardware address
E
CH
} X4&]
Reads MAC address.
Read # of open connections
E
CC
} X4*]
Set subnet mask
EX4^
CS
}
Ips
X4^]
Read subnet mask
E
CS
} X4^]
Set gateway IP address
EX4^
CG
}
Ipg
X4^]
Read gateway IP address
E
CG
} X4^]
Set administrator password
EX4(
CA
}
Ipa•
X4(]
Read administrator password
E
CA
} X4(]
Reset (clear) administrator
password
E
•CA
}
Ipa•
]
Set user password
EX4(
CU
}
Ipu•
X4(]
Read user password
E
CU
} X4(]
Reset (clear) user password
E
•CU
}
Ipu•
]
Set mail server, domainname
EX4^
,
X5)
,
X4(
CM
}
Ipm
X4^
,
X5)
,
X4(]
Read mail server, domainname
E
CM
} X4^
,
X5)
,
X4(]
Set e‑mail recipient
EX5!
,
X5@
CR
}
Ipr
X5!
,
X5@
,
]
This command sets the e‑mail recipient.
To receive e‑mail notifications, you must
then set the events that the switcher
reports, using one or more separate
Set e-mail (EM) SIS commands (on the
next page).
Example:
E
69,Jsmith@folklore.netCR
}
Ipr69,Jsmith@folklore.net,
]
Read e‑mail recipient
EX5!
CR
} X5@
,
]
FOX Matrix 3200 and 7200 Switchers • Programming Guide 68