Filter
Top Products
120
Sampling
• Solo sampling:[5 (Solo)]
While playing the internal sound generator as usual, sample
only the sound from the external input.
* Effects cannot be applied to the external input sound.
fig.SMPL05_50
3.
Make the settings for things such as the input source of the
sound to be sampled, and triggering.
•
Input Select
Specifies the input source of the sound that is to be sampled.
Value
LINE IN L/R:
INPUT jacks L/R (stereo)
LINE IN L:
INPUT jack L (mono)
MICROPHONE:
INPUT jack L (mic level)
* This cannot be set when resampling.
• Stereo Switch
Specifies whether the sound will be sampled in stereo or in
monaural. Mono sampling uses half as much memory space.
Value
MONO:
The sound will be sampled as one wave. If the sound
is stereo, the left and right signals will be mixed.
STEREO:
The sound will be sampled as two waves, L and R.
•
Pre Sample Time
The length of sound preceding the moment at which sampling
was manually or automatically initiated that will be captured in
the sample. This lets you prevent the attack portion of the sound
from being omitted from the sample.
Value:
0–1000 ms
•
Stop Trigger
Specifies how sampling will end.
Value
MANUAL:
Continue sampling until you press [STOP].
BEAT:
Sample the specified number of beats at the current
tempo (BPM).
TIME:
Sample the specified length of time.
•
Sampling Length
You can specify this if Stop Trigger is “BEAT” or “TIME.”
Value
Sampling LengthWhen Stop Trigger is “BEAT”:1–20000:Number
of beats to continue sampling
When Stop Trigger is “TIME”:00’00”010–50’00”000:length of
time to continue sampling. The maximum value will depend on
the amount of memory.
• Auto Trigger Level
Specifies the volume at which sampling will begin if you have
pressed [2 (Auto Trig)] to turn Auto Trig ON.
Value:
0–7 (A setting of 0 is the minimum.)
•
Gap Time
Specifies the length of the silences at which the sample will be
divided if the Sampling Mode is set to Auto Divide. Whenever
there is a silent region longer than the specified time, the sample
will be divided at that point, and the next sample number will be
assigned to the sound that follows.
Value:
500, 1000, 1500, 2000 ms
* This parameter is valid only when you are using Auto Divide
Sampling.
•
Input Setting:[1(INPUT SETTING)]
Makes settings for the external input (p. 118).
•
Auto Trigger:[2(AUTO TRIG)]
If this is on, sampling will begin automatically when the input
sound is detected.
•
Trim Sw:[3(TRIM SW)]
If this is turned on, the Start point and End point settings (p. 125)
will be automatically adjusted after sampling is performed, so
any silent portions at the beginning or end of the sampled sound
are excluded.
4.
In the EXT SOURCE section of the panel, use LEVEL knob to
adjust the input level of the external source.
fig.LEVEL knob
* If the volume of the external source is too high, the PEAK indicator will
light. If this occurs, turn down the LEVEL knob until the PEAK
indicator no longer lights.
* If the level of the sound to be sampled is too high, the word “CLIP” will
appear at the lower right of the level meter in the screen.
* Using a connection cable that contains a resistor can cause the sound
level to be low. Use a connection cable that does not contain a resistor.
5.
Press [8 (Start)] to begin sampling.
6.
If Stop Trigger is set to MANUAL, press [7 (Stop)] to stop
sampling.
The Sample Edit (p. 124) screen will appear.
* If you want to edit the sample, refer to p. 124.
fig.SMPL06_50
Reference_e.book 120 ページ ２００３年７月１４日 月曜日 午後３時２５分