Filter
Top Products
MuxOneNAND2G(KFM2G16Q2A-DEBx)
- 85 -
FLASH MEMORY
MuxOneNAND4G(KFN4G16Q2A-DEBx)
3.3 Reset Mode Operation
The One NAND has 4 reset modes: Cold/Warm/Hot Reset, and NAND Flash Array Reset. Section 3.3 discusses the operation of these reset
modes.
The Register Reset Table shows the which registers are affected by the various types or Reset operations.
Internal Register Reset Table
NOTE :
1a) RDYpol, RDY conf, INTpol, IOBE are reset by Cold reset. The other bits are reset by cold/warm/hot reset.
1b) The other bits except OTP
L
and OTP
BL
are reset by cold/warm/hot reset.
2) ECC Status Register & ECC Result Registers are reset when any command is issued.
3) Refer to Device ID Register F001h.
4) Resetting during IDLE state, this is valid. But resetting during BUSY state, refer to Chapter 2.8.21.
5) To read NAND Flash Write Protection status, Block Address register must be written before.
Internal Registers Default Cold Reset
Warm
Reset
(RP
)
Hot
Reset
(00F3h)
Hot
Reset
(BP-F0h)
NAND Flash
Core Reset
(00F0h)
F000h Manufacturer ID Register (R) 00ECh N/A N/A N/A N/A
F001h Device ID Register (R): MuxOneNAND (Note 3) N/A N/A N/A N/A
F002h Version ID Register (R) N/A N/A N/A N/A N/A
F003h Data Buffer size Register (R) 0800h N/A N/A N/A N/A
F004h Boot Buffer size Register (R) 0200h N/A N/A N/A N/A
F005h Amount of Buffers Register (R) 0201h N/A N/A N/A N/A
F006h Technology Register (R) 0000h N/A N/A N/A N/A
F100h Start Address1 Register (R/W): DFS, FBA 0000h 0000h 0000h 0000h N/A
F101h Start Address2 Register (R/W): DBS 0000h 0000h 0000h 0000h N/A
F102h Start Address3 Register (R/W): FCBA 0000h 0000h 0000h 0000h N/A
F103h Start Address4 Register (R/W): FCPA, FCSA 0000h 0000h 0000h 0000h N/A
F104h Start Address5 Register (R/W): FPC 0000h 0000h 0000h 0000h N/A
F107h Start Address8 Register (R/W): FPA, FSA 0000h 0000h 0000h 0000h N/A
F200h Start Buffer Register (R/W): BSA, BSC 0000h 0000h 0000h 0000h N/A
F220h Command Register (R/W) 0000h 0000h 0000h 0000h N/A
F221h System Configuration 1 Register (R/W) 40C0h 40C0h (Note1a) (Note1a) N/A
F240h Controller Status Register (R) (Note 1b)(Note 4) 0000h 0000h 0000h 0000h N/A
F241h Interrupt Status Register (R/W) - 8080h 8010h 8010h N/A
F24Ch Start Block Address (R/W) 0000h 0000h 0000h N/A N/A
F24Dh End Block Address: N/A N/A N/A N/A N/A N/A
F24Eh NAND Flash Write Protection Status (R) (Note 5) 0002h 0002h 0002h N/A N/A
FF00h ECC Status Register (R) (Note2) 0000h 0000h 0000h 0000h N/A
FF01h
ECC Result of Sector 0 Main area data Regis-
0000h 0000h 0000h 0000h N/A
FF02h
ECC Result of Sector 0 Spare area data Regis-
0000h 0000h 0000h 0000h N/A
FF03h
ECC Result of Sector 1 Main area data Regis-
0000h 0000h 0000h 0000h N/A
FF04h
ECC Result of Sector 1 Spare area data Regis-
0000h 0000h 0000h 0000h N/A
FF05h
ECC Result of Sector 2 Main area data Regis-
0000h 0000h 0000h 0000h N/A
FF06h
ECC Result of Sector 2 Spare area data Regis-
0000h 0000h 0000h 0000h N/A
FF07h
ECC Result of Sector 3 Main area data Regis-
0000h 0000h 0000h 0000h N/A
FF08h
ECC Result of Sector 3 Spare area data Regis-
0000h 0000h 0000h 0000h N/A