Filter
Top Products
RESTRICTED USE ONLY Fargo Electronics, Inc.
HDP600 High Definition Card Printer/Encoder User Guide (Rev. 2.5)
16-2
Contrast, 15-3
Contrast/Gamma, 7-42
Control panel, 15-3
Copies, 7-21
copyright/version information, 7-24
CR-100, 15-4
CR-100 patch size, 2-28
CR-79, 15-4
CR-80, 7-12
CR-80, 15-4
CR-80 and CR-100, 7-15
CR-80, CR-90 and CR-100, 7-14
CR-90, 15-4
CR-90 or CR-100, 2-28
CSA, 2-5
Cursor, 15-4
Custom 1/Custom 2 options, 7-5, 7-17, 7-19
custom Image Transfer settings., 7-5
customization options, 7-64
D
Darkness, 15-4
Data Cables, 4-70
DB-9, 15-4
DC (Direct Current), 15-4
DC Motor, 15-4
Decrease/Increase the Print Offset value, 11-10
Default, 15-4
Default button, 7-45
Defined Area(s) check box, 7-54
Defined Area(s) option, 7-52
Defrag, 15-4
Device Option tab, 4-64
Dimensions, 2-8
DIP switches (Dual In-line Package Switches), 15-4
Direct-to-Card (DTC) Printing, 15-5
direct-to-card printing, 7-4
disable printing, 7-39
Disables Magnetic Verification, 4-95
disk cleanup utility, 4-23
Display, 2-8
Dither, 15-5
dither method, 7-32
DMA (Direct Memory Access), 15-3
Dongle, 15-5
Dot, 15-5
Dot pitch, 15-5
Download, 15-5
DPI (Dot Per Inch), 15-5
DRAM (Dynamic Random Access Memory), 15-5
DRAM Memory Error, 10-2
Driver, 15-5
Duplex Printing, 15-5
dwell temperature, 7-17
Dwell Time, 7-8, 15-6
Dye Migration, 15-6
Dye-Sub Intensity setting, 4-82
Dye-Sub Intensity slide, 7-42
dye-sub printed image, 7-42
Dye-Sublimation, 2-13, 15-6
Dye-Sublimation Cyan Panel, 2-21
Dye-Sublimation Magenta Panel, 2-21
dye-sublimation ribbon Panels, 7-42
Dye-Sublimation Yellow Panel, 2-21
E
E-card, 15-6
E-card Docking Station, 15-6
ECP Mode (Enhanced Capabilities Port Mode), 15-6
edge of card, 11-24
Edge-to-Edge, 15-6
Edge-to-Edge printing, 7-17
EE Checksum Error, 10-1
EE Error, 4-4
EE Memory, 15-6
EE Memory Error, 10-1
EEPROM (Electrically Erasable Programmable Read
Only Memory), 15-6
EEPROM Erased, 4-4
embedded contaminants,
2-22, 4-78
Emissions Standards, 2-5
Enable MLE Support checkbox, 7-65
Encode Station, 2-18
Encoder (Smart Card), 15-6
Encoder (wheel), 15-7
Encoder Settings, 11-23
encoding instructions, 7-39
Encoding Mode, 7-62, 7-63
Encoding Options, 2-8
End Sentinel (ES)., 7-69
Engine, 15-7
EOF (End Of Form), 15-7
EPP (Enhanced Parallel Port), 15-7
EPROM (Electronically Programmable Read Only
Memory), 15-7
EPROM version number, 4-96
Error/Attention Screens, 2-20
Escape sequence, 15-7
ESD, 1-2, 7-2, 8-2
ESD (ElectroStatic Discharge), 15-7
Ethernet, 15-7
Examine test card, 11-22
excessive resin printing problems, 4-86
F
factory default settings/Default button, 7-49
Failed to verify the encoded mag data., 4-9
Fargo Technical Support, 13-1
Fargo Technical Support via the Web, 13-1
FCC, 2-5
feed card into encoder, 4-23
Feeder Station, 2-18
Field Separator (FS), 7-69
Film, 15-7
Film Calibration Fail Error, 4-5
Film Drive adjustment, 11-19
Film is out!, 4-6
Film Sensors are not calibrated., 4-6
Film transfers, 11-20
Firmware, 15-7
Firmware file link, 12-3