Barco HDX Projector User Manual


 
1. Safety
It is hazardous to operate without lens or shield. Lenses, shields or ultra violet screens shall be changed if they have become
visibly damaged to such an extent that their effectiveness is impaired. For example by cracks or deep scratches.
Warning: Protection from ultraviolet radiation: Do not look directly in the light beam. The lamp contained in this product is
an intense source of light and heat. One component of the light emitted from this lamp is ultraviolet light. Potential eye and skin
hazards are present when the lamp is energized due to ultraviolet radiation. Avoid unnecessary exposure. Protect yourself and
your employees by making them aware of the hazards and how to protect themselves. Protecting the skin can be accomplished
by wearing tightly woven garments and gloves. Protecting the eyes from UV can be accomplished by wearing safety glasses
that are designed to provide UV protection. In addition to the UV, the visible light from the lamp is intense and should also be
considered when choosing protective eye wear.
Exposure to UV radiation: Some medications are known to make individuals extra sensitive to UV radiation. The American
Conference of Governmental Industrial Hygienists (ACGIH) recommends occupational UV exposure for an-8 hour day to be
less than 0,1 micro-watts per square centimeters of effective UV radiation. An evaluation of the workplace is advised to assure
employees are not exposed to cumulative radiation levels exceeding these government guidelines. The exposer of this UV
radiation is allowed for only 1 hour per day for maintenance and service persons.
Cooling liquid circuit. The projector contains a cooling circuit lled with Blue antifre
eze diluted (1/3 ethanediol 2/3 Demi
water).
When the cooling circuit leaks, switch off the device and contact a service technician.
The liquid is not for household use. Keep out of reach of children. Harmful by oral intake. A
void exposure to pregnant women.
Avoid contact with eyes, skin and clothing. Avoid inhale of the noxious fumes.
When the projector is mounted above persons, mount always a lens safety cable.
To prevent re hazard
Do not place ammable or combustible materials near the projector!
Barco large screen projection products are designed and manufactured to meet the most stringent safety regulations. This
projector radiates heat on its external surfaces and from ventila
tion ducts during normal operation, which is both normal and
safe. Exposing ammable or combustible materials into close proximity of this projector could result in the spontaneous ignition
of that material, resulting in a re. For this reason, it is absolutely necessary to leave an “exclusion zone” around all external
surfaces of the projector whereby noammable or combustibl
e materials arepresent. The exclusion zone must be notless than
40 cm (16”) for all DLP projectors. The exclusion zone on the lens side must be at least 5 m. Do not cover the projector or the
lens with any material while the projector is in operation. Keep ammable and combustible materials away from the projector at
all times. Mount the projector in a well ventilated area
away from sources of ignition and out of direct sun light. Never expose
the projector to rain or moisture. In the event of re, use sand, CO
2
or dry powder re extinguishers. Never use water on an
electrical re. Always have service performed on this projector by authorized Barco service personnel. Always insist on genuine
Barco replacement parts. Never use non-Barco repl
acement parts as they may degrade the safety of this projector.
Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projector and to protect
it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the
projector too close to walls, or other similar surface. This projector should never be placed near or over a radiator or heat
register. This projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
Projection rooms must be well ventilated or cooled in order to avoid build up of heat.
Let the projector cool down completely before storing. Remove cord from the projector when storing.
Heat sensitive materials should not be placed in the path of the exhausted air or on the lamp house.
To prevent projector damage
This projector has been designed for use with a specic lamp (house) type. See installation instructions for its correct type.
The air lters of the projector must be cleaned or replaced on regular base (a "clean" booth would be monthly-minimum).
Neglecting this could result in disrupting the air ow inside the projector, causing overheating. Overheating may lead to the
projector shutting down during operation.
The projector must always be installed in a manner which ensures free ow of air into its air inlets and unimpeded evacuation
of the hot air from its cooling system.
In order to ensure that correct airow is maintained, and that the projector complies with Electromagnetic Compatibility (EMC)
requirements, it should always be operated with all of it’s covers in place.
Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from
overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product
on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. The
device should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and unplug the mains
supply immediately. Do not operate the projector again until it has been checked by qualied service personnel.
Do not block the projector cooling fans or free air movement around the projector. Loose papers or other objects may not be
nearer to the projector than 1
0 cm (4") on any side.
Do not use this equipment near water.
Special care for Laser Beams: Special care should be used when DLP projectors are used in the same room as high power
laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices
TM
in
which case there is a loss of warranty.
Never place the projector in direct sun light. Sun light on the lens can severely damage the Digital Mirror Devices
TM
in which
case there is a loss of warranty.
Save the original shipping carton and packing material. They will come in handy if you ever have to ship your equipment. For
maximum protection, repack your set as it was originally packed at the factory.
R5905032 HDX SERIES 02/03/2015
9