Filter
Top Products
52
WJ-SX150 SETUP MENU (OSD)
The WJ-SX150 SETUP MENU (SETUP MENU) enables func-
tion controls that are not available by direct operation.
Note: Only one operator can enter SETUP MENU.
■ Displaying SETUP MENU
To display SETUP MENU, follow the procedure below.
1. Confirm that the camera and peripherals are correctly
and securely connected and that all components are
turned on.
2. To execute the selection, select one of the monitors (1
to 4) by pressing the numeric button, then press the
MON (ESC) button.
The MONITOR indicator will light up.
3. Press the SETUP button while holding down the SHIFT
button on the system controller.
WJ-SX150 SETUP MENU will appear on the active mon-
itor as shown below, and the system controller's SETUP
indicator will light up.
The tree of SETUP MENU is shown in the next page.
Note: “x.xx” in SETUP MENU shows the firmware ver-
sion.
The following functions and buttons are valid in SETUP
MENU:
Joystick to UP(D): Moves the cursor up or returns to
the previous page.
Joystick to DOWN(C): Moves the cursor down or dis-
plays the next page.
Joystick to L(A): Moves the cursor to the left.
Joystick to R (B): Moves the cursor to the right.
PREV button: Selects the previous mode or parameter.
NEXT button: Selects the next mode or parameter.
Numeric buttons: Enters numerals.
CLEAR button: Deletes a character when editing a
camera title.
CAM (SET) button: Executes the selections and dis-
plays a submenu for items with the (O) mark.
MON (ESC) button: Returns to SETUP MENU or the
previous menu.
This operating instructions uses the symbols to
describe the buttons.
4. To end the setting and return to the normal view, press
the SETUP button while holding down the SHIFT button
when SETUP MENU is displayed.
The system controller's SETUP indicator will go off.
Note: The Multiplexer board version, “900 MULTIPLEX-
ER”, and “1000 MUX CAMERA TITLE” is displayed
only when the Multiplexer board is installed in the
unit.
■ Programming SETUP MENU
As shown in the tree, SETUP MENU has seven main sub-
menus:
TIME & DATE, D. S. T., SEQUENCE SETUP, ALARM
SETUP, CAMERA TITLE, SYSTEM SETUP and OPERATOR
REGISTRATION.
SEQUENCE SETUP, ALARM SETUP, CAMERA TITLE, SYS-
TEM SETUP and OPERATOR REGISTRATION are further
divided into additional submenus.
The (O) mark indicates that the item has a submenu for
more detailed setups.
Refer to the figure in next page for the composition of
SETUP MENU.
■ TIME & DATE
SETUP
SHIFT
WJ-SX150 SETUP MENU x.xx/x.xx
100 TIME&DATE Aug/21/2002 10:55 AM
200 D.S.T. ON
300 SEQUENCE
O
400 ALARMO
500 CAMERA TITLEO
600 RECORDERO
700 SYSTEMO
800 OPERATOR REGISTRATIONO
900 MULTIPLEXERO
1000 MUX CAMERA TITLEO
(Without the Multiplexer board)*
(With the Multiplexer board)
* This is the factory default setting.
WJ-SX150 SETUP MENU x.xx
100 TIME&DATE Aug/21/2002 10:55 AM
200 D.S.T. ON
300 SEQUENCEO
400 ALARMO
500 CAMERA TITLEO
600 RECORDERO
700 SYSTEMO
800 OPERATOR REGISTRATIONO
WJ-SX150 SETUP MENU x.xx/x.xx
100 TIME&DATE Aug/21/2002 10:55 AM
200 D.S.T. ON
300 SEQUENCE
O
400 ALARMO
500 CAMERA TITLEO
600 RECORDERO
700 SYSTEMO
800 OPERATOR REGISTRATIONO
900 MULTIPLEXERO
1000 MUX CAMERA TITLEO