Filter
Top Products
62 www.emersonct.com SM-EZMotion Module User Guide
If a registration sensor is seen outside of this window (not
between the WindowStart and WindowEnd positions) then
it will be ignored.
Window End
This parameter defines the end of the Registration Sensor
Valid Window relative to start position of this index. This is
an unsigned value and is relative only to starting position of
this index. Index direction does not affect this parameter.
The Registration Window End position (or distance) should
be greater than the Registration Window Start position. If a
registration sensor is seen outside of this window (not
between the WindowStart and WindowEnd positions) then
it will be ignored.
Example:
Index 0 is defined as a Registration type of index. The user
wants the index to run at velocity for 10 Revs, or until the
Torque Feedback reaches 50% continuous torque and
then continue for another 0.5 Revs.
In the Limit Distance parameter, enter 10.0.
On the registration tab, select the Analog radio button.
In the analog list box, select Torque Command
In the comparison operator list box, select ">"
In the analog value parameter, enter 50 (Units are
established on the User Units view)
In the Registration Offset parameter, enter 1.5
This index would accelerate up to its' target velocity, and
run at speed until one of the following:
The Limit Distance is approaching, and the index decels
down to zero velocity, completing the move at the Limit
Distance. At this point, the Index.#.LimitDistHit source
would activate.
Or,
The Torque Command reaches or exceeds 50%
continuous, and the index continues at speed before
decelerating to zero velocity at the registration point plus
the Registration Offset distance.
If the Registration Offset distance is in the opposite
direction from the move, or is so short that the motor
cannot stop in the specified distance at the programmed
deceleration rate, the motor will decelerate with the
programmed ramp, and then back-up to the specified
position (registration point + the Registration Offset).
Index Sources and Destinations
Sources
Index.AnyCommandComplete - Active when any index
motion command is completed. If a stop is activated before
the index has completed, this destination will not activate.
Deactivated when any new index command is initiated.
Index.#.Accelerating - This source is active while an index
is accelerating to its' target velocity. Once the index
reaches the target velocity, or begins to decelerate, the
Index.#.Accelerating source will deactivate.
Index.#.AtVel - This source activates when the target index
velocity is reached. If Feedrate override is changed or
FeedHold is activated AtVelocity shall remain active.
Index.#.AtVel will deactivate at the start of any deceleration
or acceleration. During a synchronized index, this source
could be active even without any motor motion if the master
axis stops.
Index.#.Command Complete - The
Index.#.CommandComplete source will activate when the
specific index completes its deceleration ramp. It will
remain active until the specific index is initiated again. If the
drive stop destination is used during an Index, then the
Index.#.CommandComplete will not activate.
Index.#.Command In Progress - The
Index.#.CommandInProgress source is active throughout
an entire index profile. The source activates at the
beginning of the index acceleration ramp, and deactivates
at the end of the index deceleration ramp. During a
synchronized index, this source could be active even
without any motor motion if the master axis stops.
Index.#.Decelerating - This source is active while an index
is decelerating from its' target velocity. Once the index
reaches zero velocity, or its' next target velocity, the
Index.#.Decelerating source will deactivate.
Index.#.LimitDistHit - Activated when the registration
sensor is not found before the Limit Distance is traveled. If
the Registration Window is enabled the sensor must be
activated inside the window to be recognized.
Index.#.PLSStatus - Controlled by the PLSOn and PLSOff
Points which are relative to the distance commanded since
the start of the index. Activated when index distance
command is in between the PLSOn point and PLSOff
points.
Index.ProfileLimited - For timed indexes, if the values for
Max. Velocity, Max. Acceleration, and Max. Deceleration
are such that the distance cannot be covered in the
specified time, the Index.ProfileLimited flag will activate
when the index is initiated, indicating that the index cannot
be performed as desired. The Index.ProfileLimited flag will
remain active until cleared using the
Index.ResetProfileLimited assignment or program
instruction. In this situation, the index will still operate, but
the time will be extended. In other words, the profile will be
performed using the maximums values and still cover the
specified distance, but not in the specified time.
Destinations
Index.ResetProfileLimited - If a timed index was not able to
complete in the specified time, the Index.ProfileLimited
source will activate. Index.ResetProfileLimited is used to
clear the ProfileLimited flag and acknowledge that the
index did not complete in the specified time. This can be
activated through an assignment, or through a user
program. This function is edge-sensitive, so holding it