Filter
Top Products
75
Figure 12. Configuration Main Menu (continued)
HOST
INTERFACE
(see page 115)
ETHERNET
PARAMS
(see page 125)
Bi-Tronics*
Prime Signal
Disable*
Enable
TOF Action
Reset*
Do Nothing
Buffer Size in K
1* (1-16)
Centronics
Data Bit 8
Enable*
Disable
PI Ignored
Enable*
Disable
Data Polarity
Standard*
Inverted
Resp. Polarity
Standard*
Inverted
Busy on Strobe
Enable*
Disable
Latch Data On
Leading*
Trailing
Prime Signal
Disable*
Enable
TOF Action
Reset*
Do Nothing
Buffer Size in K
1* (1-16)
Serial
Interface Type
RS-232*
RS-422
Data Protocol
XON / XOFF*
ETX / ACK
ACK / NAK
DTR
Baud Rate
9600*
19200
38400
600
1200
2400
4800
Word Length
8*
7
DIAGNOSTICS
(see page 129)
Printer Tests
Shift Recycle*
All E’s
E’s + TOF
All H’s
All Underlines
All Black
Shuttle Slow
Shuttle Fast
Shuttle Only
Phase Printer
217* (500 lpm)
123* (1000 lpm)
62* (1500 lpm)
(1 to 2000)
Paperout Adj.
Burnin Test
Print Error Log
Clear Error Log
E-Net Test Page
Test Width
Full Width*
80 col.
Paper Out Dots
40 dots*
(4-76 dots)
System Memory
x Megabytes
Print Statistics
On:
x.x Hrs.
Print:
x.x Hrs.
Print Strokes
Print Lines
11 inch Pages
Serial (cont.)
Stop Bits
1*
2
Parity
None*
Odd
Even
Mark
Sense
Data Term Ready
True*
On-Line and BNF
Off-Line or BF
False
Request to Send
On-Line and BNF*
Off-Line or BF
False
True
Buffer Size in K
1* (1-16)
Ethernet
Buffer Size in K
16* (1-16)
Auto Switching
Parallel Hotport
Port Type
Bi-Tronics*
Centronics
Ethernet
Disable
Trickle Time
1/4*
(1/4-16 sec.)
Off
Timeout
10 sec.*
(1-60 sec.)
Report Status
Disable*
Enable
Serial Hotport
Port Type
RS-232*
RS-422
Disable
Trickle Time
1/4*
(1/4-16 sec.)
Off
Timeout
10 sec.*
(1-60 sec.)
Report Status
Disable*
Enable
PRINTER
CONTROL
(see page 127)
Unidirectional
Disable*
Enable
PMD Fault
Enable*
Disable
Open Platen @BOF
Disable*
Enable
Slow Paper Slew
Disable*
Enable
Power Saver Time
15 min.*
(5 sec.-60 min.)
Disable
Instant
RIBBON
MINDER
(see page 132)
New Ribbon
Ribbon Action
Disable*
Display
Fault
Ribbon Size
60 yards*
(1-255)
Ribbon Adjust
0%*
(-99% to 99%)
Fault Action
New Ribbon*
Do Nothing
To view options, press:
Down
Up
Next
Prev
To select an option, press ENTER.
To return to main menu, press
CLEAR.
To exit menu, press ON LINE.
* = Default Setting
IP Address
xxx.xxx.xxx.xxx
Gateway Address
xxx.xxx.xxx.xxx
Subnet Mask
xxx.xxx.xxx.xxx
MAC Address
hhhhhhhhhhhh
Novell Protocol
Enable*
Disable
NetBIOS Protocol
Enable*
Disable
Novell Frame
Ethernet 802.2*
802.2 Snap
Auto Sensing
Ethernet II
Ethernet 802.3
PPM Port Number
3001*
(0-65535)
PPM Port Timeout
32 Seconds*
(1-255)
Ethernet Speed
Auto Select*
10 Half Duplex
10 Full Duplex
100 Half Duplex
100 Full Duplex