Filter
Top Products
—
8. Software commands
—
ESC N (27)D(78)D (1B)H (4E)H
Specifies the bottom margin.
(1 ≤n ≤ 255)
nn n
The number of lines to be skipped is specified by “n” and the
bottom margin is specified in the preset line feed amount.
ESC O (27)D(79)D (1B)H (4F)H
Cancels the bottom margin.
ESC P (27)D(80)D (1B)H (50)H
Specifies or cancels proportional printing.
n n n n = 0
: Cancels proportional printing.
n = 1
: Specifies proportional printing.
This command is valid when #34 PITCH LOCK is set to NO.
ESC Q (27)D(81)D (1B)H (51)H
Printer deselect
nn n
Brings the printer into the deselect state when
n=(23)H,(B9)H.
Valid when #71 SELECT IN ENABLE is set to 1 in the
EXTENDED SETUP MODE or set to I/F and the SELECT IN
signal is high.
ESC R (27)D(82)D (1B)H (52)H
Initializes the horizontal and vertical tab positions.
Clears the vertical tab position.
ESC S (27)D(83)D (1B)H (53)H
Specifies superscript or subscript.
n n n n = 0
: Specifies superscript.
n = 1
: Specifies subscript.
ESC T (27)D(84)D (1B)H (54)H
Cancels superscript or subscript.
ESC U (27)D(85)D (1B)H (55)H
Specifies or cancels uni-directional printing.
n n n n = 0
: Cancels uni-directional printing.
n = 1
: Specifies uni-directional printing.
ESC W (27)D(87)D (1B)H (57)H
Specifies or cancels double-width printing.
n n n n = 0
: Cancels double-width printing.
n = 1
: Specifies double-width printing.
ESC X (27)D(88)D (1B)H (58)H
Specifies the right and left margins.
{0 ≤n ≤ 255} {0 ≤m ≤255}
n m n m n m
ESC Y (27)D(89)D (1B)H (59)H
Specifies the 8-dot double-speed double-density graphic mode.
n1 n2 n1 n2 n1 n2
Number of data
k = n1 + n2
×
256
d1 d2 d1 d2 d1 d2
Horizontal dot density
: 120 dpi
••• dk ••• dk ••• dk
Maximum dots per line
: 1632 dot
Horizontally adjacent dots cannot be printed.
ESC Z (27)D(90)D (1B)H (5A)H
Specifies the quadruple-density graphic mode.
n1 n2 n1 n2 n1 n2
Number of data
k = n1 + n2
×
256
d1 d2 d1 d2 d1 d2
Horizontal dot density
: 240 dpi
••• dk ••• dk ••• dk
Maximum dots per line
: 3264 dot
Horizontally adjacent dots cannot be printed.
ESC [ - (27,91,45)D (1B, 5B, 2D)H
Specifies the line type.
n1 n2 n1 n2 n1 n2
Number of data
k = n1 + n2
×
256
m1 m2 m1 m2 m1 m2 m1 = 1 :
Underscore
m2 = 0
: Cancels the line specification.
m1 = 2
: Center line
m2 = 1
: Single line
m1 = 3
: Upper line
m2 = 2
: Double lines
m2 = 255
: Cancels the line specification.
●
IBM Software commands
Decimal Hex
Symbol
Function
Code
8-12