Filter
Top Products
—
8. Software commands
—
ESC [ T (27,91,84)D (1B, 5B, 54)H
Selects the code page.
(n1=4 n2=0 n3=0 n4=0)
n1 n2 n1 n2 n1 n2 n1 + n2 x 256
indicates the number of the next data.
n3 n4 n3 n4 n3 n4 n5=(01)H n6=(B5)H 437
n5 n6 n5 n6 n5 n6 (03)H (52)H 850
(03)H (59)H 857
(03)H (5A)H 858
(03)H (5C)H 860
(03)H (5F)H 863
(03)H (61)H 865
(40)H (00)H ISO-8859-1
(03)H (5D)H 861
(0F)H (07)H BRASCII
(0F)H (08)H ABICOMP
ESC [ \ (27,91,92)D (1B, 5B, 5C)H
Specifies the basic amount of line feeding.
n1 n2 n1 n2 n1 n2 (n1=4 n2=0 m1=0 m2=0 m3=0,104,180,216 m4=0,1,180,216)
m1 m2 m1 m2 m1 m2 n1 + n2 x 256
indicates the number of the next data.
m3 m4 m3 m4 m3 m4 When m3=0 and m4=216 or m3=216 and m4=0 ,
the basic line
feed pitch is 1/216 inch.
When m3=0 and m4=180 or m3=180 and m4=0
, the basic line
feed pitch is 1/180 inch.
When m3=104 and m4=1, the basic line feed pitch is 1/360 inch.
The basic line feed pitch is 1/216 inch (when not in the AGM
mode) or 1/180 inch (in the AGM mode) by default.
ESC [ d (27,91,100)D (1B, 5B, 64)H
Selects character quality.
(n1=1 n2=0)
n1 n2 n1 n2 n1 n2 n1 + n2 x 256
indicates the number of the next data.
n3 n3 n3 n3 = 0
: Not changed.
n3 =(01)H - (7F)H
Draft
n3 =(80)H - (BF)H
LQ
n3 =(C0)H -(FE)H
Emphasized LQ
n3 =(FF)H
LQ
Valid when #35 QUALITY LOCK is set to NO in the
EXTENDED SETUP MODE.
ESC [ g (27,91,103)D (1B, 5B, 67)H
Graphic mode
n1 n2 n1 n2 n1 n2 n1+n2
×
256
specifies (graphic data + 1).
m m m {0 ≤ n1 ≤255}{0 ≤n2 ≤ 255} {m = 0, 1, 2, 3, 8, 9, 11, 12, 16}
d1 d2 d1 d2 d1 d2 m
indicates the graphic mode (density) as shown below.
••• dk ••• dk ••• dk
●
IBM Software commands
Decimal Hex
Symbol
Function
Code
8-16
m = 0 8 pin 60 dpi
1 8 120
2 8 120 (*)
3 8 240 (*)
824 60
9 24 120
11 24 180
12 24 360 (*)
16 48 360 (*)
In a graphic mode marked with an asterisk
(*)
horizontally adjacent dots cannot be printed.