Filter
Top Products
DES-3500 Layer 2 Fast Ethernet Switch CLI Reference Manual
189
delete access_profile
Purpose Used to delete a previously created access profile.
Syntax
delete access_profile [profile_id <value 1-255> | all]
Description
The delete access_profile command is used to delete a previously
created access profile on the Switch.
Parameters
profile_id <value 1-255> − Enter an integer between 1 and 255 that
is used to identify the access profile that will be deleted with this
command. This value is assigned to the access profile when it is
created with the create access_profile command. The user may
enter a profile ID number between 1 – 255, yet, remember only 9
access profiles can be created on the Switch.
all − Entering this parameter will delete all access profiles currently
configured on the Switch.
Restrictions Only Administrator and Operator-level users can issue this
command.
Example usage:
To delete the access profile with a profile ID of 1:
DES-3526:admin# delete access_profile profile_id 1
Command: delete access_profile profile_id 1
Success.
DES-3526:admin#
config access_profile
Purpose Used to configure an access profile on the Switch and to define specific values that will be
used to by the Switch to determine if a given packet should be forwarded or filtered. Masks
entered using the create access_profile command will be combined, using a logical AND
operational method, with the values the Switch finds in the specified frame header fields.
Specific values for the rules are entered using the config access_profile command, below.
Syntax
config access_profile profile_id <value 1-255> [add access_id <value 1-65535> [ethernet
{vlan <vlan_name 32> | source_mac <macaddr> | destination_mac <macaddr> | 802.1p
<value 0-7> | ethernet_type <hex 0x0-0xffff>} | ip {vlan <vlan_name 32> | source_ip
<ipaddr> | destination_ip <ipaddr> | dscp <value 0-63> | [icmp {type <value 0-255> code
<value 0-255>} | igmp {type <value 0-255>} | tcp {src_port <value 0-65535> | dst_port
<value 0-65535> | flag_mask [all | {urg | ack | psh | rst | syn | fin} | udp {src_port <value
0-65535> | dst_port <value 0-65535>} | protocol_id <value 0-255> {user_define <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff>}]} | packet_content_mask {offset_0-15 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>
<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_16-31 <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_32-47 <hex 0x0-0xffffffff> <hex
0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_48-63 <hex 0x0-0xffffffff>
<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_64-79 <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>}]
port <portlist> [permit {priority <value 0-7> {replace_priority} | replace_dscp_with <value
0-63>} | deny] {time_range <range_name 32>} | delete access_id <value 1-65535>]
Description
The config access_profile command is used to configure an access profile on the Switch and
to enter specific values that will be combined, using a logical AND operational method, with
masks entered with the create access_profile command, above.
Parameters
profile_id <value 1-255> − Enter an integer used to identify the access profile that will be
configured with this command. This value is assigned to the access profile when it is created
with the create access_profile command. The profile ID sets the relative priority for the profile
and specifies an index number that will identify the access profile being created with this