Filter
Top Products
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM30
STATIONCLASSOFSERVICE
SELECT = Logical Port Number(s) (
Enter the logical port number(s) to which class of service
T
ButtodLEDs
must be assigned. See Note 3 for entering a range of ports.
Light LEDs for the port specified in the last step. A// Button/
NOTE: Shaded areas apply to
I
-________-
Priv. Override Allowed5a6
Exec. Override Allowed6
..~
DND Override Allowed6
Change T.C.O. Code9
Change Verified A.Cio
Account Codes Verified
Digital Tile. Recv. VOI~‘~
Digital Tele. Recv. V01.l~
Dial Pulse/(DTMF Off)*
Change DISA Security Code’
Change TR Override Code’ ’
Forced Acc’t Code
OCA/Busy Override Automatic”
ABR Access Enabled15
Speed Dial Allowed
Mic on at Start of Call’2
K16
on/v
LEDs marked with an “Yin the table below shoui
‘d be lit.
09
08 ) )
I
I
I
07 I I I
i : i ’ ’ i I I I
1. For more information, see the instructions preceding the record sheets.
2. Initialized data reads LEDs 01, OS, 07, and 12 ON for all ports.
3. A range of ports may be specified by entering:
lIIa3lcII
Low par
-High port
4. If this LED is turned OFF, OCA and Busy Override must be accessedmanuallyby dialing2. If kept ON, ACB and Executive Override
cannot be accessed.
5. If all stations are allowed Privacy Override, (the system will be non-private), allowing up to three telephones to talk on the same
CO line.
6.
See Program 10-2 to enable/disable Priv./Exec./DND override warning tones.
7. To change DISA code from selected stations: Dial Intercom 6 5 8 + code + Redial.
8. DP or DTMF is specified for standard telephones only, KSTU, PSTU, or PEW (Circuits 1 and 2) in DK16, QSTU in DK8.
9.
To change a four-digit Traveling Class Override (T. C. 0.) code: Dial Intercom + ODD + code + Redial.
‘““=622-Class1,623-Class2,624-Class3,625-Class4.
10. To change Verified Account Codes from selected stations: Dial Intercom + 6 5 9 + Code Number (000 - 299) for DK16; (000 - 099)
for DKB + code (1 - 15 digits) + Redial. Note that the total Account Code digit length is set in Program 60-4; all digits do not have
to be verified.
11.
To change the four-digit T. R. override codes (1 or 2) from selected stations: Dial Intercom + 6 5 4 + code + Redial; or Intercom
+ 6 5 5 + code + Redial.
12. Mic ON/OFF at start of call (LED 03 ON = Mic ON, LED 03 OFF = Mic OFF) is only in effect if Mic button lock is enabled (LED 02
= ON).
13. There are nine handset receiver volume levels, 1 - 9 (9 being the highest). The initial off-hook level can be set anywhere from level
2 to 5. Set the initial level with one of the following combinations: Level2 = 12 OFF/l 3 OFF; Level 3 = 12 ON/l 3 OFF (default level);
Level 4 = 12 OFF/13 ON; Level 5 = 12 ON/13 ON.
14. To require DISA callers to dial Verified Forced Account Codes before accessing outside CO lines, light LEDs 08 and 14 on DK16
(Port 20) or DK8, (Port 10).
15. For ABR to function, QRCU (DKB) or K4RCU (DK16) must be installed to detect busy tone.
2-66