Filter
Top Products
Network setup (CLX-3185N/CLX-3185WK/CLX-3185FN/CLX-3185FW only)_ 3
enter 192.168.1.X (X is number between 1 and 254 other than
the computer’s address).
•Subnet Mask: Enter a Subnet Mask.
•Default Gateway: Ent
er a Default Gateway.
6.Click Apply, an
d then click OK. The machine will automatically print
the Network Configuration Report. Confirm that all the settings are
correct.
7.Click Exit to close the SetIP prog
ram.
8.If necessary,
restart the computer’s firewall.
IPv4 setting using SetIP Program (Macintosh)
For using SetIP program, disable the computer firewall before continuing
by performing the following.
1.Open System Preferences.
2.Click Secu
rity.
3.Click th
e Firewall menu.
4.Turn
firewall off.
The following instructions may vary from your model.
1.Conn
ect your machine to the network with a network cable.
2.In
sert the Installation CD-ROM, and open the disk window, select
MAC_Installer > MAC_Printer > SetIP > SetIPapplet.html.
3.Doub
le-click the file and Safari will automatically open, then select
Trust. The browser will open the SetIPapplet.html page that shows
the printer’s name and IP address information.
4.High
light the printer information row and select the Setup icon, which
is the second icon from the left in the application menu bar. A TCP/IP
Configuration window will open.
If the printer was not shown in the information row, select the
Manual Setting icon (third from left) to open the TCP/IP
Configuration window.
5.Ente
r the machine’s new information into the configuration window as
follows. In a corporate intranet, you may need to have this
information assigned by a network manager before proceeding.
•MAC Addres
s: Find the machine’s MAC address from the Network
Configuration Report and enter it without the colons. For
example, 00:15:99:29:51:A8 becomes 0015992951A8.
•IP Ad
dress: Enter a new IP address for your printer.
For example, if your computer’s IP add
ress is 192.168.1.150,
enter 192.168.1.X (X is number between 1 and 254 other than
the computer’s address).
•Su
bnet Mask: Enter a Subnet Mask.
•Default Gateway: Ent
er a Default Gateway.
6.Select Apply, then OK, an
d OK again. The printer will automatically
print the configuration report. Confirm that all the settings are correct.
Quit Safari. You may close and eject the installation CD-ROM. If
necessary, restart the computer’s firewall. You have successfully
changed the IP address, subnet mask, and gateway.
IPv4 setting using SetIP Program (Linux)
SetIP program should be automatically installed during the printer driver
installation.
1.Pri
nt the machine’s network configuration report to find your machine’s
MAC address.
2.Ope
n the /opt/Samsung/mfp/share/utils/.
3.Doub
le-click the SetIPApplet.html file.
4.Click to
open the TCP/IP configuration window.
5.En
ter the network card’s MAC address, IP address, subnet mask,
default gateway, and then click Apply.
When you enter the MAC address, enter it without a colon(:).
6.T
he machine prints the network information. Confirm all the settings
are correct.
7.C
lose the SetIP program.
Network parameter setting
You can also set up the various network settings through the network
administration programs such as SyncThru™ Web Admin Service and
SyncThru™ Web Service.
Restoring factory default settings
You may need to reset the machine to the factory default settings when
machine that you are using is connected to new network environment.
Restoring factory default settings using control panel
1.Press Menu on the control panel.
2.Press the left/
right arrow until Network appears and press OK.
3.Press the left/
right arrow until Clear Setting appears and press OK.
4.Press the left/
right arrow until Yes appears and press OK.
5.T
urn off and restart machine to apply settings.
Restoring factory default settings using SyncThru™
Web Service
1.Start a web browser such as Internet Explorer, Safari or Firefox and
enter your machine’s new IP address in the browser window.
For example:
2.Click Go to access the SyncThru™ Web Service.
3.Click Log
in on the upper right of the website.
The Lo
gin window appears.
4.T
ype in the ID and Password, and then click Login.
If it is your first time logging into
SyncThru™ Web Service, type in
the below default ID and password.
•ID: admin
•Password: sec00000
5.Click Sett
ings > Network Settings.
6.Click R
estore Default on the left pane of the website.
7.Click Cl
ear.
8.Click Yes when
the confirmation window appears.
9.Click OK whe
n the success window appears.
10.Turn
off and restart machine to apply settings.
Installing wired network-connected machine’s
driver
Windows
You can set up the machine driver, follow the steps below.
This is recommended for most users. All components necessary for
machi
ne operations will be installed.
1. Make
sure that the machine is connected to the network or USB and
powered on.
2. Inse
rt the supplied software CD into your CD-ROM drive.