ADC 3 Switch User Manual


 
ADC Telecommunications, Inc.
8 Technology Drive
Westborough, MA 01581
ADC Telecommunications, Inc. (herein referred to as “ADC”) may revise this manual at any time without notice.
All statements, technical information, and recommendations contained herein are believed to be accurate and
reliable at the time of publication but are presented without any warranty of any kind, express or implied,
(including the warranties of merchantability and fitness and against infringement or interferrence with your
enjoyment of the information) and you are solely responsible for your use of this manual with any equipment
or software described herein.
This manual (in whole or in part, including all files, data, documentation, and digital and printed copies made
therefrom) is protected by United States copyright laws, international treaties and all other applicable national
or international laws. With the exception of materials printed for use by a user who is authorized by separate
license from ADC, this manual may not, in whole or part, be modified, excerpted, copied, photocopied,
translated, or reduced to any electronic medium or machine readable form, without ADC’s written consent
obtained prior thereto.
The CUDA 12000 is listed to UL 1950 Third Edition and CAN/CSA-C22.2 No. 950-95 Third Edition compliance.
The following information is for compliance by Class A devices with FCC regulations: the equipment described
in this manual has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC regulations. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it
was probably caused by the equipment or one of its peripheral devices. If the equipment causes interference to
radio or television reception, try to correct the interference by using one or more of the following methods.
Turn television or radio antenna until the interference stops.
Move equipment to one side or the other of the television or radio.
Move equipment farther away from the television or radio.
Plug equipment into an outlet that is on a different circuit from the television or radio. (That is, make
certain the equipment and the television or radio are on circuits controlled by different circuit breakers or
fuses.)
Modifications to this equipment that are not authorized by ADC could void the FCC certification and UL
approval and negate your authority to operate the equipment.
This manual is provided by ADC on an ”AS IS, WITH ALL FAULTS” basis, without any representation or
warranty of any kind, either express or implied, including without limitation any representations or
endorsements regarding use of, the results of, or performance of the equipment or software, its
appropriateness, accuracy, reliability, or correctness. You assume the entire risk as to the use of this
manual. ADC does not assume liability for the use of this manual beyond its original purchase price.
In no event will ADC be liable for additional direct or indirect damages including any lost profits, lost
savings, lost revenue or other incidental or consequential damages arising from any defects, or the
use or inability to use this manual or the equipment or software described herein, even if ADC has
been advised of the possibility of such damages.
Cuda 12000, MeshFlow, CudaView, FastFlow Broadband Provisioning Manager and CableOnce are trademarks
of ADC Telecommunications, Inc. CableLabs® is a registered trademark of Cable Television Laboratories, Inc.
Java® is a registered trademark of Sun Microsystems, Inc. in the United States and other countries. Jini™ is a
trademark of Sun Microsystems, Inc. in the United States and other countries.
The Cuda 12000 includes RSA BSAFE cryptographic or security protocol software from RSA security. The Cuda
12000 contains an integrated DOCSIS-compliant provisioning server. Use of this provisioning functionality is
restricted to licensed authorization. ADC will not support provisioning for for your use thereof if you are not
authorized by the appropriate software license to use such provisioning.
All other company and product names mentioned herein may be trademarks of their respective companies.