Chapter 4 Parameters|
4-34 Revision August 2008, 03VE, SW V2.04
Pr. Explanation Settings
Factory
Setting
VF
VFPG
SVC
FOCPG
TQRPG
39: Ground current detection error (Hd3)
○ ○ ○ ○ ○
40: Auto tuning error (AuE)
○ ○ ○
41: PID feedback loss (AFE)
○ ○ ○ ○ ○
42: PG feedback error (PGF1)
○
○ ○
43: PG feedback loss (PGF2)
○
○ ○
44: PG feedback stall (PGF3)
○
○
45: PG slip error (PGF4)
○
○
46: PG ref input error (PGr1)
○ ○ ○ ○ ○
47: PG ref loss (PGr2)
○ ○ ○ ○ ○
48: Analog current input loss (ACE)
○ ○ ○ ○ ○
49: External fault input (EF)
○ ○ ○ ○ ○
50: Emergency stop (EF1)
○ ○ ○ ○ ○
51: External Base Block (B.B.)
○ ○ ○ ○ ○
52: Password error (PcodE)
○ ○ ○ ○ ○
53: Reserved
○ ○ ○ ○ ○
54: Communication error (cE1)
○ ○ ○ ○ ○
55: Communication error (cE2)
○ ○ ○ ○ ○
56: Communication error (cE3)
○ ○ ○ ○ ○
57: Communication error (cE4)
○ ○ ○ ○ ○
58: Communication Time-out (cE10)
○ ○ ○ ○ ○
59: PU time-out (cP10)
○ ○ ○ ○ ○
60: Brake transistor error (bF)
○ ○ ○ ○ ○
61: Y-connection/Δ-connection switch error (ydc)
○ ○ ○ ○
62: Decel. Energy Backup Error (dEb)
○ ○ ○ ○ ○
63: Slip error (oSL)
○ ○ ○ ○
64: Broken belt error (bEb)
○ ○ ○ ○ ○
65: Error PID feedback signal of tension (tdEv)
○ ○ ○ ○ ○
06-32
Output Frequency for
Malfunction
0.00~655.35 Hz 0.00
○ ○ ○ ○ ○
06-33
Output AC Voltage for
Malfunction
0.0~6553.5 V 0.0
○ ○ ○ ○ ○
06-34
DC Voltage for
Malfunction
0.0~6553.5 V 0.0
○ ○ ○ ○ ○
06-35
Current Value for
Malfunction
0.00~655.35 Amp 0.00
○ ○ ○ ○ ○
06-36
IGBT Temperature for
Malfunction
0.0~6553.5 °C 0.0
○ ○ ○ ○ ○
Group 8 High-function PID Parameters
New parameters 08-21~08-99
Pr. Explanation Settings
Factory
Setting
VF
VFPG
SVC
FOCPG
TQRPG
08-00
Input Terminal for PID
Feedback
0: No function
1: Negative PID feedback from external terminal AVI
(Pr.03-00)
2: Negative PID feedback from PG card (Pr.10-15,
skip direction)
3: Negative PID feedback from PG card (Pr.10-15)
4: Positive PID feedback from external terminal AVI
(Pr.03-00)
5: Positive PID feedback from PG card (Pr.10-15,
skip direction)
6: Positive PID feedback from PG card (Pr.10-15)
0
○ ○ ○ ○
08-01
Proportional Gain (P)
0.0~500.0%
80.0
○ ○ ○ ○
0: Disable
0
○ ○ ○ ○
08-21
Tension Control
Selection
1: Closed-loop, speed mode
○ ○ ○ ○
2: Line speed, speed mode
○ ○ ○ ○
3: Reserved
4: Open-loop, torque mode
○