Filter
Top Products
Introduction
6
VG-Series Modero Touch Panels
1200VG Panel Specifications (Cont.)
Other AMX Equipment: Several items are included within both the Video and RGB Kits. Any items
not specifically included within those kits can be considered as optional
accessories.
• CB-TP12 (FG031-10): - 12" metallic conduit box for Wall Mount
installations.
• CC-USB (Type-A) to Mini-B 5-Wire programming cable (FG10-5965)
• Kensington Lock Bracket (FG2259-10) (optional only with NXTs)
• MAX-CSE MAX Video Encoder (FG2178-70)
• MB-TP12 Universal VESA Mounting Box for 12" WallMount panels
(FG031-50):
- Black metallic VESA back box (62-0031-50)
- Black plastic cover (with grommet opening) (60-0031-50)
- Four Phillips pan-head screws (#8-32 x 0.50 Black) (80-0146-02)
- Tie Wrap (Large) (45-0009A) (for use with NXA-MTC/RGB)
- Twelve Under-cut Phillips-head screws (#6-32 x 0.500 Black) (80-
0139)
- Strain relief grommet (45-0004-03) (for use with CA2250-50)
- Universal VESA Mount grommet (45-0032-01)
(for use with NXA-MTC/RGB)
• NXA-AVB/ETHERNET Breakout Box (FG2254-10)
- Also comes included within Video Kits.
• NXA-AVB/RGB Breakout Box (FG2254-11)
- Also comes included within RGB Kits.
• NXA-BASE/B (FG2255)
- Wireless base for Table Top touch panels (NXT models only).
• NXA-KLB Kensington Lock Kit for NXT panels (FG2259-10)
(optional only with NXT models)
• NXA-MTC/RGB Modero 10’ foot Table Top Cable (with RGB connector)
(CA2250-70). This cable is not wall-rated for NXD models.
• NXA-PCI80211G Wireless Card (FG2255-04)
• NXA-RGBKIT RGB upgrade kit for Composite Video touch panels
(FG2255-11):
- NXA-AVB/RGB Breakout Box (FG2254-11)
- NXA-MTC/RGB Modero 10’ foot Table Top Cable
(with RGB connector) (CA2250-70)
- NXA-RGB internal RGB/VGA Interface Card (FG2260)
- NXA-RGBCBL, 15-pin to 5X BNC RGB Breakout cable (FG2250-80)
- NXT Table Top replacement I/O plate (with RGB connector opening)
(62-2250-59)
- NXD WallMount replacement adhesive overlay for existing I/O plate
(53-2250-03)
• Note: The NXT replacement I/O plate is a single piece which is
meant to be swapped-out with the pre-existing plate shipped with
Composite Video panels. On NXD panels, the RGB connector
opening is pre-drilled into the I/O plate but can only be accessed by
replacing the adhesive cover and maintaining the existing overlay.
When upgrading NXD panels with this kit, don’t replace the NXD I/O
plate, only the adhesive cover.
• NXA-RGBCBL, 15-pin to 5X BNC RGB Breakout cable (FG2250-80)
• NXA-RK12 (FG2904-50)
- RackMount kit for 12" Wall Mount touch panels (NXD models only)
• NXT-BP (FG2250-10)
- Battery pack for Table Top panels. Provides 4 hours of continual
operation (NXT models only)