Filter
Top Products
II CORE BLOCK: BCU (Bus Control Unit)
B-II-4-44 EPSON S1C33210 FUNCTION PART
A18IO: Areas 18–17 internal/external access selection (DF) / Access control register (0x48132)
A16IO: Areas 16–15 internal/external access selection (DE) / Access control register (0x48132)
A14IO: Areas 14–13 internal/external access selection (DD) / Access control register (0x48132)
A12IO: Areas 12–11 internal/external access selection (DC) / Access control register (0x48132)
A8IO: Areas 8–7 internal/external access selection (DA) / Access control register (0x48132)
A6IO: Area 6 internal/external access selection (D9) / Access control register (0x48132)
A5IO: Areas 5–4 internal/external access selection (D8) / Access control register (0x48132)
Select either internal access or external access for each area.
Write "1": Internal access
Write "0": External access
Read: Valid
When AxxIO is set to "1", the internal device that mapped to the corresponding area is accessed. When AxxIO is set
to "0", the external device is accessed.
At cold start, these bits are set to "0" (external access). At hot start, these bits retain their status before being
initialized.
A18EC: Areas 18–17 little/big endian method selection (D7) / Access control register (0x48132)
A16EC: Areas 16–15 little/big endian method selection (D6) / Access control register (0x48132)
A14EC: Areas 14–13 little/big endian method selection (D5) / Access control register (0x48132)
A12EC: Areas 12–11 little/big endian method selection (D4) / Access control register (0x48132)
A10EC: Areas 10–9 little/big endian method selection (D3) / Access control register (0x48132)
A8EC: Areas 8–7 little/big endian method selection (D2) / Access control register (0x48132)
A6EC: Area 6 little/big endian method selection (D1) / Access control register (0x48132)
A5EC: Areas 5–4 little/big endian method selection (D0) / Access control register (0x48132)
Select either little endian or big-endian method for accessing each area.
Write "1": Big-endian
Write "0": Little-endian
Read: Valid
When AxxEC is set to "1", the corresponding area is accessed in big-endian method. When AxxEC is set to "0", the
area is accessed in little-endian method. When using area 10 as the boot area, fix A10EC at "0" (little-endian).
At cold start, these bits are set to "0" (little-endian). At hot start, these bits retain their status before being initialized.
A18AS: Areas 18–17 address strobe signal (DF) / G/A read signal control register (0x48138)
A16AS: Areas 16–15 address strobe signal (DE) / G/A read signal control register (0x48138)
A14AS: Areas 14–13 address strobe signal (DD) / G/A read signal control register (0x48138)
A12AS: Areas 12–11 address strobe signal (DC) / G/A read signal control register (0x48138)
A8AS: Areas 8–7 address strobe signal (DA) / G/A read signal control register (0x48138)
A6AS: Area 6 address strobe signal (D9) / G/A read signal control register (0x48138)
A5AS: Areas 5–4 address strobe signal (D8) / G/A read signal control register (0x48138)
Enable/disable the exclusive address strobe signal output.
Write "1": Enabled
Write "0": Disabled
Read: Valid
If AxxAS is set to "1", the exclusive address strobe signal is output from #GAAS (P21) pin when the corresponding
area is accessed. If AxxAS is set to "0", the signal output is disabled.
At cold start, these bits are set to "0" (disabled). At hot start, these bits retain their status before being initialized.