Filter
Top Products
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch CLI Reference Guide
425
The Connectivity Fault Management (CFM) commands in the Command Line Interface (CLI) are listed (along with the
appropriate parameters) in the following table.
Command Parameters
create cfm md <string 22> level <int 0-7>
config cfm md <string 22> { mip [ none | auto | explicit ] | sender_id [ none | chassis | manage |
chassis_manage ] } (1)
create cfm ma <string 22> md <string 22>
config cfm ma <string 22> md <string 22> { vlanid <vlanid 1-4094> | mip [none | auto | explicit | defer] |
sender_id [none | chassis | manage | chassis_manage | defer] | ccm_interval [10ms |
100ms | 1sec | 10sec | 1min | 10min] | mepid_list [add | delete] <mepid_list> }(1)
create cfm mep <string 32> mepid <int 1-8191> md <string 22> ma <string 22> direction [inward | outward]
port <port>
config cfm mep [ mepname <string 32> | mepid <int 1-8191> md <string 22> ma <string 22>] {state [enable
| disable] | ccm [enable | disable] | pdu_priority <int 0-7> | fault_alarm [all | mac_status |
remote_ccm | error_ccm | xcon_ccm | none] | alarm_time < centisecond 250-1000> |
alarm_reset_time < centisecond 250-1000>}(1)
delete cfm mep [mepname <string 32> | mepid <int 1-8191> md <string 22> ma <string 22>]
delete cfm ma <string 22> md <string 22>
delete cfm md <string 22>
enable cfm
disable cfm
config cfm ports <portlist> state [ enable | disable]
show cfm ports <portlist>
show cfm { [ md <string 22> { ma <string 22> { mepid <int 1-8191> } } | mepname <string 32> ] }
show cfm fault { md <string 22> { ma <string 22> } }
show cfm port <port> {level <int 0-7> | direction [inward | outward] | vlanid <vlanid 1-4094>}
cfm loopback <macaddr> [ mepname <string 32> | mepid <int 1-8191> md <string 22> ma <string 22> ]
{num <int 1-65535> | [length <int 0-1500> | pattern <string 1500>] | pdu_priority <int 0-7> }
cfm linktrace <macaddr> [ mepname <string 32> | mepid <int 1-8191> md <string 22> ma <string 22>] {ttl
<int 2-255> | pdu_priority <int 0-7>}
show cfm linktrace [ mepname <string 32> | mepid <int 1-8191> md <string 22> ma <string 22>] { trans_id
<uint>}
delete cfm linktrace { [ md <string 22> { ma <string 22> { mepid <int 1-8191> } } | mepname <string 32> ] }
show cfm mipccm
config cfm mp_ltr_all [ enable | disable ]
show cfm mp_ltr_all
show cfm
remote_mep
[ md <string 22> ma <string 22> mepid <int 1-8191> | mepname <string 32> ]
remote_mepid <int 1-8191>
show cfm pkt_cnt { [ ports <portlist> { [ rx | tx ] } | [ rx | tx ] | ccm ] }
clear cfm pkt_cnt { [ ports <portlist> { [ rx | tx ] } | [ rx | tx ] | ccm ] }
Each command is listed, in detail, in the following sections: