Filter
Top Products
Parameter Command Setting
Reference
Oscillator Source
SENSe<
chan
>:ROSCillator:SOURce
<
source
>
INTernal (the digitizer’s internal 20 MHz oscillator)
Input Port SENSe<
chan
>:FUNCtion "<
function
>
<
port
>"
"VOLT <port>" (where <
port
> is set by the
(@<
input port
>) parameter of MEASure? or CONFigure)
Measurement
range
SENSe<
chan
>:VOLTage:DC:RANGe
<
range
>
set according to the <
expected value
> parameter of
MEASure? or CONFigure
Input Impedance INPut<
port
>:IMPedance <
impedance
>
50
Ω (when <
port
> is 1 or 2)
10 MHz Input
Filter
INPut<
port
>:FILTer:LPASs:STATe <
mode
>ON
Input State INPut<
port
>:STATe <
mode
> ON (for all ports)
Arm Source ARM:STARt:SOURce<
n
> <
source
> IMMediate (for
n
= 1)
HOLD (for
n
= 2)
Arm Count ARM:STARt:COUNt 1
Arm Delay ARM:STARt:DELay 0
Trigger Source TRIGger:STARt:SOURce <
source
>TIMer1
Pre-arm Readings SENSe<
chan
>:SWEep:OFFSet:POINts
<
count
>
0
Trigger Count TRIGger:STARt:COUNt <
number
>
SENSe<
chan
>:SWEep:POINts <
number
>
<
number
> is set to the (<
size
>) parameter of MEASure? or
CONFigure
Sample Rate
(single)
TRIGger:STARt:TIMer1 <
period
> 50 ns
Sample Rate
(dual)
TRIGger:STARt:TIMer2 <
period
> 100 ns
Output State OUTPut:ECLTrg<
n
>:STATe <
mode
>
OUTPut:TTLTrg<
n
>:STATe <
mode
>
OUTPut:EXTernal1:STATe <
mode
>
OFF
OFF
OFF
Output Feed OUTPut:ECLTrg<
n
>:FEED <
source
>
OUTPut:TTLTrg<
n
>:FEED <
source
>
OUTPut:EXTernal1:FEED <
source
>
"TRIGger:STARt" (ECLTrg0) "EXTernal1" (ECLTrg1)
"ARM:STARt"
"TRIGger:STARt"
VME Bus Mode VINStrument:CONFigure:VME:MODE
<
mode
>
OFF
VME Bus Feed VINStrument:CONFigure:VME:FEED
<source >
"MEMory:BOTH32"
Local Bus Mode
(HP E1429B only)
VINStrument:CONFigure:LBUS:MODE
<
mode
>
OFF
Local Bus Feed
(HP E1429B only)
VINStrument:CONFigure:LBUS:FEED
<
source
>
"MEMory:BOTH"
Reading Format FORMat[:DATA] <
type
>[,<
length
>] ASCii, 9
Data label DIAGnostic:CHANnel[<chan >]:LABel
<
label
>
0 (channel 1)
0 (channel 2)
Table 1-3. Digitizer Configuration using MEASure? and CONFigure
Chapter 1 Getting Started 35