Filter
Top Products
xStack DGS-3600 Series Layer 3 Gigabit Ethernet Managed Switch CLI Manual
228
config access_profile (for Ethernet)
Parameters
access profile that will be configured with this command. This value is assigned to the
access profile when it is created with the create access_profile command. The lower the
profile ID, the higher the priority the rule will be given.
add access_id <value 1-128> - Adds an additional rule to the above specified access
profile. The value specifies the relative priority of the additional rule. Up to 128 different
rules may be configured for the Ethernet access profile.
!"auto_assign – Choose this parameter to configure the Switch to automatically assign
a numerical value (between 1 and 128) for the rule being configured.
ethernet - Specifies that the Switch will look only into the layer 2 part of each packet to
determine if it is to be filtered or forwarded based on one or more of the following:
• vlan <vlan_name 32> − Specifies that the access profile will apply to only this
previously created VLAN.
• source_mac <macaddr> − Specifies that the access profile will apply to only packets
with this source MAC address. MAC address entries may be made in the following
format: 000000000000-FFFFFFFFFFFF
• destination_mac <macaddr> − Specifies that the access profile will apply to only
packets with this destination MAC address. MAC address entries may be made in the
following format: 000000000000-FFFFFFFFFFFF
• 802.1p <value 0-7> − Specifies that the access profile will apply only to packets with
this 802.1p priority value.
• ethernet_type <hex 0x0-0xffff> − Specifies that the access profile will apply only to
packets with this hexadecimal 802.1Q Ethernet type value in the packet header.
port <portlist> | all - The access profile for Ethernet may be defined for each port on the
Switch. Up to 128 rules may be configured for each port. The user may select all ports by
entering the all parameter. The port list is specified by listing the lowest switch number and
the beginning port number on that switch, separated by a colon. Then the highest switch
number, and the highest port number of the range (also separated by a colon) are
specified. The beginning and end of the port list range are separated by a dash. For
example, 1:3 specifies switch number 1, port 3. 2:4 specifies switch number 2, port 4. 1:3-
2:4 specifies all of the ports between switch 1, port 3 and switch 2, port 4 − in numerical
order. Non-contiguous portlist entries are separated by a comma. (ex: 1:1-1:3,1:7-1:9)
permit – Specifies that packets that match the access profile are permitted to be forwarded
by the Switch.
• priority <value 0-7> − This parameter is specified to re-write the 802.1p default
priority previously set in the Switch, which is used to determine the CoS queue to
which packets are forwarded. Once this field is specified, packets accepted by the
Switch that match this priority are forwarded to the CoS queue specified previously
by the user.
• {replace_priority} − Enter this parameter if you want to re-write the 802.1p default
priority of a packet to the value entered in the Priority field, which meets the criteria
specified previously in this command, before forwarding it on to the specified CoS
queue. Otherwise, a packet will have its incoming 802.1p user priority re-written to its
original value before being forwarded by the Switch.
rx_rate – Use this to limit Rx bandwidth for the profile being configured. This rate is
implemented using the following equation – 1 value = 64kbit/sec. (ex. If the user selects a
rx rate of 10 then the ingress rate is 640kbit/sec.) The user many select a value between 1-
156249 or no limit. The default setting is no_limit.
counter [enable | disable] – Use this parameter to enable the counter function. When
enabled, this counter will count the number of packets that match the profile stated with
this command. If the counter command is enabled using the flow_meter command, the
counter command here will be overridden and therefore will not count packets. This
command is optional and the default setting is disabled.
mirror - Selecting mirror specifies that packets that match the access profile are mirrored to
a port defined in the config mirror port command. Port Mirroring must be enabled and a
target port must be set. Remember, Port Mirroring cannot cross-box, that is they cannot
span across switches in a switch stack.
deny – Specifies that packets that do not match the access profile are not permitted to be