Filter
Top Products
xStack DGS-3600 Series Layer 3 Gigabit Ethernet Managed Switch CLI Manual
239
Access Profile ID: 1 TYPE : Packet Contact
======================================================================
Owner : ACL
MASK Option :
offset_chunk_1 : 1 value : 0x11111111
Access ID : 1 Mode: Permit Rx Rate(64Kbps): no_limit
(Replaced)Priority: 2
Ports: 1:8
Time range: Trinity
Total Matched Counter : 0
Offset_chunk_1 : 1 value : 0x11111111
======================================================================
Unused Entries : 127
DGS-3600:4#
create cpu access_profile
Purpose
Used to create an access profile specifically for CPU Interface Filtering on the Switch and to
define which parts of each incoming frame’s header the Switch will examine. Masks can be
entered that will be combined with the values the Switch finds in the specified frame header
fields. Specific values for the rules are entered using the config cpu access_profile command,
below.
Syntax
create cpu access_profile profile_id <value 1-5> [ethernet {vlan | source_mac <macmask
000000000000-ffffffffffff> | destination_mac <macmask 000000000000-ffffffffffff> |
ethernet_type} | ip {vlan | source_ip_mask <netmask> | destination_ip_mask <netmask> |
dscp | [icmp {type | code} | igmp {type} | tcp {src_port_mask <hex 0x0-0xffff> |
dst_port_mask <hex 0x0-0xffff>} | flag_mask [all | {urg | ack | psh | rst | syn | fin}]} |
udp {src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex 0x0-0xffff>} | protocol_id_mask
<hex 0x0-0xff>} {user_define_mask <hex 0x0-0xffffffff>}]} | packet_content_mask {offset 0-
15 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset
16-31 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> |
{offset 32-47 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>
| {offset 48-63 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff> | {offset 64-79 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex
0x0-0xffffffff> | ipv6 {class | flowlabel | source_ipv6_mask <ipv6mask> |
destination_ipv6_mask <ipv6mask>}]}
Description
The create cpu access_profile command is used to create an access profile used only for CPU
Interface Filtering. Masks can be entered that will be combined with the values the Switch finds in
the specified frame header fields. Specific values for the rules are entered using the config cpu
access_profile command, below.
Parameters
ethernet − Specifies that the Switch will examine the layer 2 part of each packet header.
• vlan − Specifies that the Switch will examine the VLAN part of each packet header.
• source_mac <macmask> - Specifies to examine the source MAC address mask. MAC
address entries may be made in the following format: 000000000000-FFFFFFFFFFFF
• destination_mac <macmask> - Specifies to examine the destination MAC address mask.
MAC address entries may be made in the following format: 000000000000-FFFFFFFFFFFF
• ethernet_type − Specifies that the Switch will examine the Ethernet type value in each
frame’s header.
ip − Specifies that the Switch will examine the IP address in each frame’s header.
• vlan − Specifies a VLAN mask.
• source_ip_mask <netmask> − Specifies an IP address mask for the source IP address.
• destination_ip_mask <netmask> − Specifies an IP address mask for the destination IP
address.
• dscp − Specifies that the Switch will examine the DiffServ Code Point (DSCP) field in each
frame’s header.
• icmp − Specifies that the Switch will examine the Internet Control Message Protocol (ICMP)
field in each frame
’
s header