Filter
Top Products
Hitachi Gigabit Router GR2000 Series Enhanced Version Configuration Commands, Vol. 2
5-30 GR2K-GA-0014
Ver. 07-02
bgp4+: the peer group option must be the
same for policy group
The settings of peer group option in the policy group are different.
The settings of peer group option in the policy group must be the
same.
bgp4+: the peer option is link-local address,
but the internal peeras group is not supported
link-local address peering
The link local address is defined in the address of the internal peer.
Define the global address or site local address in the peer address of
the internal peer.
bgp4+:the refresh option must be specified
with ipv6-uni
Parameters other than ipv6-uni are specified in the parameter of a
refresh option. Do not specify parameters other than ipv6-uni in the
parameter of a refresh option.
bgp4+:when the peer address is link-local
address, gateway option must not be
specified
The peer address is a link local address, but a gateway option is
defined. Do not define a gateway option when a link local address is
defined in the peer address.
configuration check error Configuration information check error. If the identifiers (<id>) to be
designated by the "attribute-list" command, the "network-filter"
command and the "route-filter" command contain unusable
characters, modify them to the correct identifiers (<id>).
dampen-flap: incorrect suppression
parameters
The parameter specified in dampen-flap definition is invalid. Specify
so as to meet the condition of reuse-below < suppress-above
<max-flap.
dampen-flap: invalid keep-history-time value
at <value> not in range 1 to 86400
The specified keep history time is invalid. Specify within the range of
1 to 86400.
<Value>: Specified keep history time
dampen-flap: invalid max-flap value at
<value> not in range 1 to 30
The specified maximum flap value is invalid. Specify within the range
of 1 to 30.
<Value>:Specified maximum flat value
dampen-flap: invalid reach-decay-time value
at <value> not in range 1 to 3600
The specified reach decay time is invalid. Specify within the range of
1 to 3600.
<Value>: Specified reach decay time
dampen-flap: invalid reuse-below value at
<value> not in range 1 to 30
The specified reuse value is invalid.
Specify within the range of 1 to 30.
<Value>: Specified reuse value
dampen-flap: invalid suppress-above value at
<value> not in range 1 to 30
The specified suppress value is invalid. Specify within the range of 1
to 30.
<Value>: Specified suppress value.
dampen-flap: invalid unreach-decay-time
value at <value> not in range 1 to 3600
The specified unreach decay time is invalid. Specify within the range
of 1 to 3600.
<Value>: Specified unreach decay time
dampen-flap: out of range The parameter-specified range is exceeded in the input command
syntax. Numeric values of more than 4294967296 are contained.
Reconfirm a parameter.
dampen-flap: syntax error Syntax error
export: address not IPv6 Addresses other than an IPv6 prefix are specified.
Specify the IPv6 prefix.
export: address should not be:: A default address is specified in an address.
Specify addresses other than the local host address.export: address
should not be v4-compatable.
export: address should not be v4-compat An IPv4-compatible address is specified in an address.
Specify addresses other than the IPv4-compatible address.
export: address should not be v4-mapped An IPv4 mapped address is specified in an address. Specify
addresses other than the IPv4 mapped address.
export: Attribute-filter " <Name>" cannot be
specified
Filter information inherent to IPv4 is defined in IPv6. Do not specify
the filter information inherent to IPv4.
<Name>: Specified identifier
Table 5-5 Routing Protocol Error Messages (continued)