Filter
Top Products
Configuration Error Messages
GR2K-GA-0014 5-41
Ver. 07-02
ospf: invalid retransmit-interval value at
<Value> not in range 1 to 65535
In the OSPF area definition, the retransmit-interval value is out of the
valid range. Specify a value within the range of 1 to 65535.
<Value>: Specified retransmit-interval value
ospf: invalid router-dead-interval value at
<Value> not in range 1 to 65535
In the OSPF definition, the router-dead-interval value is out of valid
range. Specify a value within the range of 1 to 65535.
<Value>: Specified router-dead-interval value
ospf: invalid seconds value at <Value> not in
range 0 to 4294967295
Specified timer value is invalid.
Specify a value within the range of 0 to 4294967295.
<Value>: Specified timer value
ospf: invalid transit-delay value at <Value> not
in range 1 to 65535
In the OSPF definition, the transit-delay value is out of valid range.
Specify a value within the range of 1 to 65535.
<Value>: Specified transit-delay value
ospf: invalid vpn number value at <Value> not
inrange1to<Max_Value>
The range of VPN value is invalid. Specify a value within the range of
1 to <Max_Value>.
<Value>: Specified VPN number
<Max_Value>: Maximum VPN number
ospf: key id must be between 0 and 255 Specified MD5 authentication key ID is invalid. Specify a value within
the range of 0 to 255.
ospf: keys cannot have same start time MD5 authentication message digest generation start time is
duplicated. Do not duplicate the start time.
ospf: mask not contiguous Bit 1 of the specified mask does not continue. Use a mask where bit
1 continues.
ospf: minute must be between 0 and 59 Specified time (minute) is invalid. Specify a value within the range of
0to59.
ospf: month must be between 1 and 12 Specified month is invalid. Specify a value within the range of 1 to 12.
ospf: multipath option not valid for vpn route The Multipath option is defined for VPN. VPN does not support
multipath option.
ospf: neighbor-id must be an IP address The IP address defined to neighborhood is invalid. Specify in IP
address format.
ospf: net range already specified Network parameter is already specified in OSPF area definition.
Do not duplicate a networks parameter.
ospf: Non-masked bits not zero for <Address>
masklen <Masklen>
In masklen, 1 is specified for non-masked bit of the specified
address. Set non-masked bit 0.
<Address>: Specified address
<Masklen>: Specified mask length
ospf: Non-masked bits not zero for <Address>
mask <Mask>
In mask, 1 is specified for non-masked bit of specified address.
Specify 0 to non-masked bit 0.
<Address>: Specified Address
<Mask>: Specified mask
ospf: nssa option not valid for backbone Nssa option is defined in a backbone area. Do not defined a nssa
option in a backbone area.
ospf: out of range The parameter-specified range is exceeded in the input command
syntax. Numeric values of more than 4294967296 are contained.
Reconfirm a parameter.
ospf: Router ID not defined Router ID is not defined. Specify the Router ID.
ospf: secondary auth was overwritten by md5
for virtual link to <Neighbor ID> in Domain
<Domain ID> [on VPN <VPN ID>].
In a specified virtual link, both MD5 authentication and the 2nd
authentication key are defined. Delete the unnecessary
authentication method.
<Neighbor ID>: router ID of the adjacent OSPF virtual link router
<Domain ID>: specified domain No. of the OSPF virtual link
<VPN ID>: specified VPN No. of the OSPF virtual link.
ospf: stop accept time must be later than start
accept time
MD5 authentication message digest accept end time is earlier than
start time. Set the value so start time is earlier than end time.
Table 5-5 Routing Protocol Error Messages (continued)