Filter
Top Products
Configuration Error Messages
GR2K-GA-0014 5-69
Ver. 07-02
Can not set replace_user_priority because
penalty_dscp is already defined.
It is not possible to set the VLAN priority rewrite value because the
contract bandwidth violation dscp rewrite value is defined. Delete the
contract bandwidth violation dscp rewrite value in order to set the
VLAN priority rewrite value.
Can not set replace_user_priority because
penalty_tos or penalty_dscp is already
defined.
It is not possible to set the VLAN priority rewrite value because the
contract bandwidth violation tos rewrite value or the contract
bandwidth violation dscp rewrite value is defined. Delete the contract
bandwidth violation tos rewrite value or the contract bandwidth
violation dscp rewrite value in order to set the VLAN priority rewrite
value.
Can not set replace_user_priority because
replace_exp is already defined.
It is not possible to set the VLAN priority rewrite value because the
exp field rewrite value is defined. Delete the exp field rewrite value in
order to set the VLAN priority rewrite value.
Can not set replace_user_priority because
tos_map or dscp_map is already defined.
It is not possible to set the VLAN priority rewrite value because
"tos_map" or "dscp_map" is defined. Delete "tos_map" or
"dscp_map" in order to set the VLAN priority rewrite value.
Can not set replace_user_priority because
upc or min_rate or max_rate is already
defined.
It is not possible to set the VLAN priority rewrite value because
bandwidth setting or minimum bandwidth guarantee and maximum
bandwidth limit are defined. Delete bandwidth setting or minimum
bandwidth guarantee and maximum bandwidth limit in order to set
the VLAN priority rewrite value.
Can not set same min_rate and max_rate
value in one flow list configuration.
No setting is possible because the minimum band assurance value is
greater than or equivalent to that of the maximum band restriction.
For the minimum band assurance, specify a value smaller than the
maximum band restriction.
Can not set scan_extension. In a flow filter, an S/W search flag cannot be set when the list number
is in the range of 1 to 20000. Specify the S/W search flag when the
list number is in the range of 40001 to 60000.
Can not set scan_extension because forward
or drop not specified.
An S/W search flag cannot be set simultaneously with parameters
other than forward or drop.
Can not set scan_extension because protocol
ip not specified.
An S/W search flag cannot be set because ip is not specified in the
upper protocol. To set an S/W search flag, specify ip in the upper
protocol.
Can not set tcp protocol. In specifying the high-order protocol, 6(tcp) cannot be specified.
Specify the “tcp” by using the packet flow detecting conditions.
Can not set these parametors(replace_tos,
replace_dscp, tos_map, dscp_map,
replace_exp) in the same flow list
configuration.
The tos rewriting value, dscp rewriting value, and tos_map,
dscp_map, and exp field rewriting values cannot be set
simultaneously. Specify them individually.
Can not set tos_map or dscp_map because
priority or discard is already defined.
tos_map or dscp_map cannot be set because the output priority or
queuing priority has been defined. To set the tos_map or dscp_map,
delete the output priority or queuing priority.
Can not set tos_map or dscp_map because
replace_exp is already defined.
tos_map or dscp_map cannot be set because the exp field rewrite
value has been defined. To set the tos_map or dscp_map, delete the
exp field rewrite value.
Can not set tos_map or dscp_map because
replace_tos or replace_dscp is already
defined.
tos_map or dscp_map cannot be set because the tos rewriting value
or dscp rewriting value has been defined. To set the tos_map or
dscp_map, delete the tos rewriting value or dscp rewriting value.
Can not set tos_map or dscp_map because
replace_user_priority is already defined.
It is not possible to set "tos_map" or "dscp_map" because the VLAN
priority rewrite value is defined. Delete the VLAN priority rewrite
value in order to set "tos_map" or "dscp_map".
Can not set udp protocol. In specifying the high-order protocol, 17(udp) cannot be specified.
Specify the “udp” by using the packet flow detecting conditions.
Table 5-8 Flow Information Error Messages (continued)