Filter
Top Products
Hitachi Gigabit Router GR2000 Series Enhanced Version Configuration Commands, Vol. 2
5-50 GR2K-GA-0014
Ver. 07-02
static: invalid octet value at <Value> not in
range 0 to 255
More than 255 values are defined in dot notation. Specify value
within the range of 0 to 255.
<Value>: Specified value
static: invalid pollcount value at xxx not in
range 1 to 10
Polling count is out of valid range. Specify value within the range of 1
to 10.
<Value>: Specified polling count
static: invalid pollinterval value at <Value> not
inrange5to180
Polling timer value is out of valid range. Specify value within the
range of 5 to 180.
<Value>: Specified polling timer value
static: Invalid pollinterval Polling timer value is invalid. Specify value in the multiples of 5.
static: invalid preference value at <Value> not
inrange2to255.
Preference value is invalid. Specify a value within the range of 2 to
255.
<Value>: Specified preference value.
static: invalid vpn number value at <Value>
not in range 1 to <Max_Value>
VPN number is out of valid range. Specify value within the range of 1
to <Max_Value>.
<Value>: Specified VPN number
<Max_Value>Maximum VPN number
static: IPv6 prefix cannot be linklocal in
configuration
The link local address is specified in the network address. Do not use
the link local address.
static: IPv6 prefix cannot be multicast in
configuration
The multicast address is specified in the network address. Do not
use the multicast address.
static: IPv6 static interface statement should
be used for non- broadcast I/F
The broadcast interface is specified in the specified interface in the
static definition. To specify the interface, specify the point-to-point
interface.
static: linklocal address should be followed by
%(IPv6 interface name)
An interface name is not specified in the specified link local address.
Specify an interface name with the percent (%) interposed when
specifying a link local address.
static: mask not contiguous Bit 1 of the specified mask does not continue. Use a mask where bit
1 continues.
static: multipath option not valid for vpn route The multipath option has been defined relative to the VPN route.
Do not define the multipath option relative to the VPN route.
static: Non-masked bits not zero for
<Address> mask <Mask>
In the mask specification, 1 is set to the non-masked bit of the
specified address. Set non-masked bit 0.
<Address>: Specified address
<Mask>: Specified mask
Static: Non-masked bits not zero for
<Address> masklen <Masklen>
In the masklen specification, 1 is set to the non-masked bit of the
specified address. Set non-masked bit 0.
<Address>: Specified address
<Masklen>: Specified mask length
static: not IPv6 prefix Addresses other than an IPv6 prefix are specified. Specify IPv6
prefix.
static: out of range The parameter-specified range is exceeded in the input command
syntax. Numeric values of more than 4294967296 are contained.
Reconfirm a parameter.
static: poll option not valid for vpn
remote-gateway
Polling option is defines in a VPN remote route. Do not define a
polling option in a VPN remote route.
static: remote-gateway <IPv6 Prefix> is not
global/site-local IPv6 address
Addresses other than a global address or site local address are
specified. Specify the global address or site local address for
remote-gateway. <IPv6 Prefix>: Specified local address
static: syntax error Syntax error
The total number of {targets|IPv6 static
gateways} (<Value>) is more than the
maximum permitted (256)
Total number of specified targets is more than maximum acceptable
value. Specify a number up to 256.
<Value>: Total number of specified targets
Table 5-5 Routing Protocol Error Messages (continued)