Filter
Top Products
Hitachi Gigabit Router GR2000 Series Enhanced Version Configuration Commands, Vol. 2
5-42 GR2K-GA-0014
Ver. 07-02
ospf: stop generate time must be later than
start generate time
MD5 authentication message digest generation end time is earlier
than start time. Set the value so start time is earlier than end time.
ospf: stub option not valid for backbone Stub parameter is specified in the OSPF backbone definition.
Do not specify a stub parameter in a backbone area.
ospf: syntax error Syntax error
ospf: this Router ID and Neighbor ID must be
different
This Router ID and Neighbor ID are the same.
Specify the different IDs to this Router and Neighbor.
ospf: transit-area can not be the
’backbone’area
The transit area of virtual link is defined outside the backbone area.
Set virtual link other than backbone area.
ospf: unknown authentication type: <Value> In the OSPF definition, authentication type is illegal. For
authentication type, specify “simple” or “md5.”
<Value>: Specified authentication type
ospf: virtual links only allowed in
’backbone’area
The virtual link is defined outside the backbone area. Set virtual link
within backbone area.
ospf: year must be after 1970 The year is before 1970. Specify a year after 1970.
ospf6: 2 or more areas have been defined:
need to configure backbone
Two or more OSPFv3 areas are defined, but a backbone area is not
defined. Define a backbone area.
ospf6: domain <Domain Number> duplicated he OSPFv3 domain number is duplicate-defined. Do not
duplicate-define the OSPFv3 domain number.
ospf6: duplicate area The area ID of OSPFv3 is duplicated for definition. Specify area ID
so that it is not duplicated.
ospf6: duplicate entry at <Prefix>/<Prefixlen> The network range is defined in duplication in the OSPVv3 definition.
Specify the range so that the network range will not be duplicated.
<Prefix>: Specified prefix
<Prefixlen> Specified prefix length
ospf6: duplicate ospf interface parameter --
“cost”
In the area definition of OSPFv3, the interface cost of an interface
parameter is double-defined. Do not double-define an interface cost.
ospf6: duplicate ospf6 clause OSPFv3 is double-defined. Delete one of the definitions.
ospf6: duplicate virtual link The pair of the passage area and the adjacent router ID has already
been defined in the hypothetical link definition of the OSPFv3.
Specify the pair so that the pair of the passage area and the adjacent
router ID will not be duplicated.
ospf6: error in common options --possible
duplicate or conflicting option?
In the area definition of OSPFv3, the interface cost of an interface
parameter is double-defined. Do not double-define an interface
option.
ospf6: Interface not found at ’ <Interface
Name>’
The interface of the specified interface name cannot be found.
Specify it by using the defined interface name.
<Interface Name>: Specified interface name
ospf6: invalid area-number value at ’<Value>’
not in range 1 to 4294967295
OSPFv3 area ID is invalid. Specify within the range of 0.0.0.1 to
255.255.255.255.
<Value>: Specified area ID
ospf6: Invalid domain configuration value at ’5’
not in range 0 to 4
The number of OSPFv3 domain configuration definitions exceeds
four upper-limit values. Delete any of the OSPFv3 domain
configuration definitions.
ospf6: invalid domain-number value at
<Domain Number> not in range 1 to 65535
The OSPFv3 domain number is invalid. Specify within the range of 1
to 65535.
<Domain Number>: Specified domain number
ospf6: invalid export-type value at ’<Value>’
not in range 1 to 2
The AS external type is invalid. Specify within the range of 1 to 2.
<Value>: Specified AS external route type
ospf6: invalid external-route-tag value at
<Value> not in range 0 to 2147483647
The AS external tag value is invalid. Specify within the range of 1 to
2147483647.
<Value>: Specified AS external tag value
Table 5-5 Routing Protocol Error Messages (continued)