Filter
Top Products
Hitachi Gigabit Router GR2000 Series Enhanced Version Configuration Commands, Vol. 2
5-84 GR2K-GA-0014
Ver. 07-02
label_switched_path: duplicate ’to <Address>’
in ’<LSP name>’
This is a duplicated definition of the "to parameters."
<Address>: Specified address
<LSP name>: Specified LSP name
label_switched_path: duplicate vpn in ’<LSP
name>’
This is a duplicated definition.
<LSP name>: Specified LSP name
label_switched_path: either ’to’ or
explicit_route_name is needed in ’<LSP
name>’
Destination is unknown because “to” and the explicit_route_name
has not been designated. Set at least either one of them.
<LSP name>: Specified LSP name
label_switched_path: flow_map ip address
should no be same as ’to <Address>’
’<Mask>’
The IP designation is incorrect. The value designated by “to” has
been designated in flow-map.
<Address>: Specified address
<Mask>: Specified mask
label_switched_path: invalid flow_map IP
address ’<Address>’ in ’<LSP name>’
IP address is invalid.
<Address>: Specified address
<LSP name>: Specified LSP name
label_switched_path: invalid mask value
’<value>’ in ’to <Address>’ notin1to32in
’<LSP name>’
The masklen values for the “to parameters” are incorrect. Set the
mask between 1 and 32.
<value>: Specified mask length
<Address>: Specified address
<LSP name>: Specified LSP name
label_switched_path: invalid mask value
’<Mask>’ in ’<LSP name>’
Mask value is invalid.
<Mask>: Specified mask
<LSP name>: Specified LSP name
label_switched_path: invalid mask value
<Mask> in ’to <Address>’ in ’<LSP name>’
The masklen values for the “to parameters” are incorrect.
<Mask>: Specified mask
<Address>: Specified address
<LSP name>: Specified LSP name
label_switched_path: invalid mask value at
’<value>’ not in 1 to 32 in ’<LSP name>’
FLOW_MAP mask value is out of range. Set the mask between 1
and 32.
<value>: Specified mask length
<LSP name>: Specified LSP name
label_switched_path: invalid remote_vpn
value at ’<remote_vpnid>’ not in range 1 to
1000000 in ’<LSP name>’
Remote_vpn value is out of range. Specify a value within the range
of 1 to 1000000
<remote_vpnid>ÅFRemote vpn value
<LSP name>: Specified LSP name
label_switched_path: invalid retry_interval
value ’<Seconds>’ not in range 10 to 600 in
’<LSP name>’
retry_interval value is out of range. Specify a value within the range
of 10 to 600.
<Seconds>: retry_interval value
<LSP name>: Specified LSP name
label_switched_path: invalid ’to <Address>’ in
’<LSP name>’
The IP address for the “to parameters” is incorrect.
<Address>: Specified address
<LSP name>: Specified LSP name
label_switched_path: invalid vpn value at
’<vpnid>’ not in range 1 to 1000000 in ’<LSP
name>’
Vpn value is out of range. Specify a value within the range of 1 to
1000000
<vpnid>: Specified vpn value
<LSP name>: Specified LSP name
label_switched_path: last entry of
explicit_routes must be same in ’<LSP
name>’
If “to” is not specified, the final entries to explicit_route used for
label_switched_path and secondary_label_switched_path must
agree with each other.
<LSP name>: Specified LSP name
Table 5-10 MPLS Information Error Messages [ROUTE-OS7] (continued)