Filter
Top Products
NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1
Page 509
Message Center Interface M-26
Programming
STEP 1: ASYD - System Data 1, Index 28, Bits 0-4. Assign a Miscellaneous Timer Counter (MTC) used to
calculate the message-sending Guard Timer for Message Center.
Timer = MTC x 128ms. Normally a Guard Timer is not required. If not required, assign data “0” to
these bits.
System Data 1, Index 28, Bit 5. Is Message Waiting Lamp setting from the Message Center to be used?
0/1: No/Yes.
System Data 1, Index 29, Bits 0-4. Assign which I/O port will act as the MESSAGE CENTER
INTERFACE. Bit 0 as Port 0 is always used as a Maintenance Administration Terminal (MAT). Bit 1
= Port 1, Bit 2 = Port 2; Bit 3 = Port 3; Bit 4 = Port 4; Bit 5 = Port 5, for a maximum of 2 ports.
System Data 1, Index 34, Bit 0 &1.
b2, b1 = “00”; no parity and output data Bit 7 is “0”.
System Data 1, Index 70, Bit 0. Called Number Display on the console for DID and TIE Line calls
must be enabled. Assign Bit 0 as data “1” when System Data 2, Index 6, Bit 7 is also enabled.
System Data 1, Index 78, Bit 0. CALLING NUMBER DISPLAY-D
term
[C-24D] must be enabled.
Assign Bit 0 as data “1”.
System Data 1, Index 78, Bit 1. CALLING STATION STATUS DISPLAY-D
term
[C-22D] must be
enabled. Assign Bit 1 as data “1”.
Note: Index 116, Port 0 is assigned as data 02H, MAT.
System Data 2, Index 6, Bit 0. Is MCI service with UCD groups to be enabled? 0/1: No/Yes.
System Data 2, Index 7, Bit 1. Is MCI service for calls via the Attendant Console to be enabled? 0/1:
No/Yes.
STEP 2: AIOC - Assign the function and attribute data of the IOC ports.
FCCS Programming
This data setting describes the additional FCCS service data after the non-FCCS service data has been
programmed. Note that the data setting for FCCS service varies depending on the node.
STEP 1: ASYDL - System Data 1, Index 641 Bit 1. Designate output numbers for MCI ICS format.
Note 1
0/1 = Physical (station) number/Telephone number
System Data 1, Index 832. Assign the FPC (Fusion Point Code) of the node providing the MC
Note 2
System Data 1, Index 833, Bit 0. Interface type for MCI. 0/1 = IOC/LAN interface. Note 2
System Data 1, Index 833, Bit 1. Text format for MCI. 0/1 = ICS/IMX format. Note 1
Note:
When more than a 5 digit telephone number is assigned, designate 1 = IMX format.
This data is required for the LAN interface type
STEP 1: ASYDL - System Data 1, Index 529, Bits 0 and 1. Parity check method of SMDR/MCI with LAN
interface.
b1, b0: 00 = No Parity
01 = Odd Parity
10 = Even Parity
System Data 1, Index 833, bit 2. Assignment of how to output the Message Center Information for
LAN connection.
0/1=Dual output/Single Output
System Data 1, Index 834, Bit 0. 0/1 = MC0 for LAN is not mounted/mounted.
Note 1
System Data 1, Index 834, Bit 1. 0/1 = MC1 for LAN is not mounted/mounted. Note 1